This article addresses the problem of induction heating in its application to the FDM/FFF 3D manufacturing. One of the major problems of the FDM/FFF is the instability of layer-to-layer adhesion quality, and on the larger scale - maintaining the homogeneity of material inside the whole printed object. Approach for mitigating and/or resolving of those problems, based on the fast and reliable control of the extruded material temperature during the printing process was proposed. Such approach uses specially created testbed system, consists of the ultra-low weight induction heated nozzle and fast temperature controller. This equipment enables rapid heating and cooling of the nozzle at low input power. On the contrary, using of the nozzle with the minimal thermal mass poses the problems of maintaining even heat distribution on the nozzle surface, and therefore inside the heated material. Multiphysics FEM model for the electromagnetic and thermal problem for the proposed nozzle and inductor configuration was formulated, and numerically solved using COMSOL 5.2a. Parametric optimization of the inductor form and heating signal frequency was conducted. Series of the experiments with the optimized inductor construction were made using the proposed testbed, showing significant increase of the heating speed and uniform heat distribution on the nozzle surface, and therefore in the final printed object quality. Experimental data for the all stages of conducted research is provided.
An approach for improving and maintaining consistent fusion quality of the deposited material during FDM 3d-printing is proposed. This approach is based on the nozzle temperature control during the printing process to adjust the polymer extrusion temperature with a speed and accuracy adequate to the FDM process. High frequency induction heating of the lightweight nozzle (<1 g) was used. To control the temperature of a lightweight nozzle, the resonant temperature measurement method based on the analysis of the high frequency eddy currents is proposed. To determine the parameters of the nozzle and the inductor as a plant, a FEM model of the inductive heating of the nozzle and a simulated model of a serial-parallel resonant circuit containing inductor were developed. Linearization of the automatic control system was performed to ensure the equal quality of regulation when operating in a wide temperature range. The quality of regulation, stability of the system, and coefficients of the PID controller were evaluated using a simulated model of the control system. A number of test samples were printed from various materials, and tensile stress testing was carried out. The developed control method reduces the nozzle temperature control error from 20 to 0.2 °C and decreases control delay by more than six times.
An approach for improving and maintaining a consistent weld quality of the deposited material during the FFF printing process is proposed. The approach is based on the analysis of the printing process thermal cycle and the real-time nozzle temperature control. The mathematical model of the FFF printing process has been developed with the use of real-time control in the algorithm of numerical implementation. The successful solution of the thermal conductivity problem made it possible to determine segment-wise heating settings for use during the printing process, resulting in a high and stable quality of welding. Comparison of the results of modeling with other well-known mathematical models of the FFF printing process and experimental results showed the adequacy of the proposed model. A maximum deviation of 17.7% between the simulation results and the thermography data was observed. The proposed model was verified using rectangular 3D polylactide shapes printed with and without regulation of the power of the heat source according to the previously estimated settings. The overall quality of regulation, stability of the system, and the PI coefficients of the controller were evaluated using a simulated model of the control system. The results of the experiment fully correspond with the modeling results.
One of the biggest challenges of fused deposition modeling (FDM)/fused filament fabrication (FFF) 3D-printing is maintaining consistent quality of layer-to-layer adhesion, and on the larger scale, homogeneity of material inside the whole printed object. An approach for mitigating and/or resolving those problems, based on the rapid and reliable control of the extruded material temperature during the printing process, was proposed. High frequency induction heating of the nozzle with a minimum mass ( 300 W) heating system, an indirect (eddy current) temperature measurement method was proposed. It is based on dynamic analysis over various temperature-dependent parameters directly in the process of heating. To ensure better temperature measurement accuracy, a series-parallel resonant circuit containing an induction heating coil, an approach of desired signal detection, algorithms for digital signal processing and a regression model that determines the dependence of the desired signal on temperature and magnetic field strength were proposed. The testbed system designed to confirm the results of the conducted research showed the effectiveness of the proposed indirect measurement method. With an accuracy of ±3 °C, the measurement time is 20 ms in the operating temperature range from 50 to 350 °C. The designed temperature control system based on an indirect measurement method will provide high mechanical properties and consistent quality of printed objects.
The multi-scale study of rock properties is a necessary step in the planning of oil and gas reservoir developments. The amount of core samples available for research is usually limited, and some of the samples can be distracted. The investigation of core reconstruction possibilities is an important task. An approach to the real-size reconstruction of porous media with a given (target) porosity and permeability by controlling the parameters of FFF 3D printing using CT images of the original core is proposed. Real-size synthetic core specimens based on CT images were manufactured using FFF 3D printing. The possibility of reconstructing the reservoir properties of a sandstone core sample was proven. The results of gas porometry measurements showed that the porosity of specimens No.32 and No.46 was 13.5% and 12.8%, and the permeability was 442.3 mD and 337.8 mD, respectively. The porosity of the original core was 14% and permeability was 271 mD. It was found that changing the layer height and nozzle diameter, as well as the retract and restart distances, has a direct effect on the porosity and permeability of synthetic specimens. This study shows that porosity and permeability of synthetic specimens depend on the flow of the material and the percentage of overlap between the infill and the outer wall.
Inter-pass forging with different degrees of deformation during WAAM of Inconel 718 specimens (single-stage, three passes; two-stage, six passes) was investigated. Macrostructural analysis of the specimens showed that inter-pass forging led to a recrystallized structure. Alternation of layers with different grain shapes (columnar and equiaxed) is observed throughout the height of the specimens. Increasing the number of passes improves the mechanical properties of the material (tensile strength, yield strength, microhardness). A finite element model of inter-pass forging was developed to determine the effect of inter-pass surface deformation during WAAM on the residual stress–strain state. The non-stationary formulation was replaced with a quasi-static one. Johnson–Cook material constants were obtained for the deposited Inconel 718 material, including the effect of forging. Verification of the mathematical model was performed using a wall (specimen 2) deposited with single-stage forging. The deviation between the simulation results and the experiment did not exceed 15%. It was found that the sequence and number of passes significantly affect residual strain and displacements but have little effect on residual stress. Numerical modeling showed that the depth of plastic deformation exceeds the melting depth when depositing the subsequent layer, ensuring the preservation and accumulation of the inter-pass forging effect throughout the deposition process.