Post-seismic reinforcement is extensively used to repair structural elements of buildings hit by strong earthquakes, while pre-seismic reinforcement can be very convenient to improve the seismic performance of buildings designed according to less stringent standards than current. One of the most commonly used techniques for both pre and post-seismic retrofit of structures is that of wrapping elements previously identified as weak or damaged with sheets of fiber-reinforced polymers (FRP). This technique may be in fact more advantageous than other strengthening approaches, due to speed of placement, low environmental impact and small load increase. Non-linear methods of analysis can be very helpful for planning the retrofit strategy and assessing in advance its effectiveness. Based on non-linear static and dynamic numerical analyses, the effectiveness of the FRP pre-seismic reinforcement on the global performance of buildings was investigated in this paper with reference to a residential Italian building designed according to obsolete standards. The seismic capacity of the building, before and after the FRP retrofit, was assessed and the efficacy of the seismic rehabilitation was evaluated. The results show that, by improving the local resistance of the most vulnerable elements and the global ductility of the building, the FRP wrapping of the ground-floor columns of the considered building has an important impact on the overall seismic response of the structure, although it cannot entirely avoid undesirable global collapse mechanisms.
Engineering practitioners do not usually include soil-structure interactions in building design; rather, it is common to model and design foundations as embedded joints with joint–based reactions. In some cases, foundation structures are modeled as rigid bodies, embedding the first story into lower vertical elements. Given that the effects of underground floors on the seismic response are not generally included in current building design provisions, it has been little explored in the literature. This work compares and analyzes models to study the effects of different underground stories modeling approaches using earthquake vibration data recorded for the 16–story Alcazar building office in downtown Viña del Mar (Chile). The modeling expands beyond an embedded first story structure to soil with equivalent springs, representing soil-structure interaction (SSI), with varying rigid soil homogeneity. The building was modeled in a finite element software considering only dead load as a static load case because the structure remained in the framing stage when the monitoring system was operating. The instruments registered 72 aftershocks from the 2010 Maule Earthquake, and this study focused on 11 aftershocks of different hypocenters and magnitudes to collect representative information. The comparisons between empirical records and models in this study showed a better fit between the model and the real vibration data for the models that do consider the SSI using horizontal springs attached to the retaining walls of the underground stories. In addition, it was observed that applying a stiffness reduction factor of 0.7 to all elements in deformation verification models for average-height buildings was suitable to analyze the behavior under small earthquakes; better results are obtained embedding the structure in the foundation level than embedding in the street level; the use of horizontal springs with Kuesel’s model with traction for the analysis of the structure yields appropriate results; it is necessary to carefully select the spring constants to be used, paying special attention to the vertical springs. Even though the results presented herein indicate that the use of vertical springs to simulate the SSI of the base slab can result in major differences concerning the real response, it is necessary to obtain more data from instrumentation across a wider variety of structures to continue to evaluate better design and modeling practices. Similarly, further analyses, including nonlinear time-history and high-intensity events, are needed to best regulate building design.
Estimating the dynamic characteristics of instrumented built structures from seismic vibration data collected from built civil structures is essential input information for structural model updating and assessing the health of structures. This study focuses on the earthquake acceleration time histories obtained from several events recorded during its construction phase by accelerometers placed throughout an office building located in Viña del Mar (Chile) to determine its modal features. To this end, the data obtained were analyzed to compare the building’s dynamic properties obtained with two different modal identification techniques. MATLAB programs were developed to implement both methods. The stochastic subspace identification technique for linear systems developed by van Overschee and de Moor was used to study the dynamic properties of the building. In contrast, the nonparametric method employed herein uses correlations and spectral analysis based on the Welch transform in the frequency domain. The investigation demonstrated that both methods identify similar frequencies and that the obtained translational mode shapes exhibit good agreement. Furthermore, the identified frequencies are congruent with the design frequencies.
El uso de sitios en pendiente para la construcción de estructuras es problemático, principalmente por dos condiciones: la variación de la respuesta sísmica de sitio, producto de la pendiente; y la modificación en la estructuración para dar cuenta de los desniveles en la base de la estructura. Estas condiciones han generado importantes daños sísmicos en áreas de altas pendientes en terremotos pasados. Este estudio busca evaluar las posibles diferencias en la respuesta sísmica producto de estas dos condiciones especiales, evaluadas de forma desacoplada. Para ello, se ejecuta una serie de análisis tiempo-historia, utilizando registros sísmicos modificados por la pendiente, sobre un grupo de estructuras con diferente ángulo basal. Las estructuras son primeramente diseñadas y evaluadas en respuesta no lineal mediante análisis pushover. Se obtienen mayores variaciones en la respuesta producto de la variación en la estructuración (escalonada) que producto del efecto topográfico, el cual, sin embargo, incrementa los efectos antes mencionados tanto en daño como en niveles de desplazamiento. Las aceleraciones verticales inducidas por la topografía son perjudiciales para el desempeño estructural, observándose más daño (incursión en el rango inelástico) en las estructuras cuando éstas se consideran en los análisis, así como diferencias importantes en los niveles de carga axial en los elementos verticales.