Molybdenum disulfide (MoS2) has been universally demonstrated to be an effective electrocatalytic catalyst for hydrogen evolution reaction (HER). However, the low conductivity, few active sites and poor stability of MoS2-based electrocatalysts hinder its hydrogen evolution performance in a wide pH range. The introduction of other metal phases and carbon materials can create rich interfaces and defects to enhance the activity and stability of the catalyst. Herein, a new defect-rich heterogeneous ternary nanocomposite consisted of MoS2, NiS and reduced graphene oxide (rGO) are synthesized using ultrathin αNi(OH)2 nanowires as the nickel source. The MoS2/rGO/NiS-5 of optimal formulation in 0.5 M H2SO4, 1.0 M KOH and 1.0 M PBS only requires 152, 169 and 209 mV of overpotential to achieve a current density of 10 mA cm−2 (denoted as η10), respectively. The excellent HER performance of the MoS2/rGO/NiS-5 electrocatalyst can be ascribed to the synergistic effect of abundant heterogeneous interfaces in MoS2/rGO/NiS, expanded interlayer spacings, and the addition of high conductivity graphene oxide. The method reported here can provide a new idea for catalyst with Ni-Mo heterojunction, pH-universal and inexpensive hydrogen evolution reaction electrocatalyst.
Bimetallic metal-organic frameworks (BMOFs) have shown a superior oxygen evolution reaction (OER) performance, attributed to the synergistic effects of dual metal sites. However, the significant role of these dual-metal synergies in the OER is not yet fully understood. In this study, we employed density functional theory to systematically investigate the OER performance of NiAl- and NiFe-based BMOFs by examining all possible spin states of each intermediate across diverse external potentials and pH environments. We found that the spin state featuring a shallow hole trap state and Ni ions with a higher oxidation state serve as strong oxidizing agents, promoting the OER. An external potential-induced spin crossover was observed in each intermediate, resulting in significant changes in the overall reaction and activation energies due to altered energy levels. Combining the constant potential method and the electrochemical nudged elastic band method, we mapped the minimum free energy barriers of the OER under varied external potential and pH by considering the spin crossover effect for both NiAl and NiFe BMOFs. The results showed that NiFe exhibits better OER thermodynamics and kinetics, which is in good agreement with experimentally measured OER polarization curves and Tafel plots. Moreover, we found that the improved OER kinetics of NiFe not only is attributed to lower barriers but also is a result of improved electrical conductivity arising from the synergistic effects of Ni-Fe dual-metal sites. Specifically, replacing the second metal Al with Fe leads to two significant outcomes: a reduction in both the band gap and the effective hole mass compared to NiAl, and the initiation of super- and double-exchange interactions within the Ni-F-Fe chain, thereby enhancing electron transfer and hopping and leading to the improved OER kinetics.
Defect tolerance, which plays a crucial role in the outstanding photoelectric performance of hybrid organic–inorganic perovskites (HOIPs), is dynamically responsive to illumination. Continuous illumination can induce local structural reorganization leading to dynamic PL enhancement.
Inorganic fullerene-like tungsten disulfide particles have been proved to have good anti-friction and anti-wear properties as lubricating materials. As far as we know, however, when it is used as a lubricant additive, its behavior and action mechanism in the friction process are rarely studied. Herein, IF–WS2 particles were synthesized by a Chemical Vapor Deposition (CVD) method. The effect of IF–WS2 particle concentrations in the PAO6 oil on the tribological behaviors was investigated with a four-ball wear machine at both 75 and 100 °C. Additionally, the analyzed morphology and composition of nanomaterials and worn surfaces were analyzed by Scanning electron microscopy (SEM), Transmission Electron Microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The friction behavior in actual working conditions was studied by a wear testing machine. The experimental results show that compared with the original PAO6 oil, at a dispersion of 0.25 wt% in PAO6 oil, the IF–WS2 particles showed the best performance in terms of coefficient of friction, wear scar diameter and wear mass, which significantly reduced by 27%, 43% and 87%, respectively. At the same time, in the process of friction, it was found that IF–WS2 particles accumulated in the depressions to fill the scratches, and adsorption films and chemical films, including FeS2, WS2 and WO3, were formed on the worn surfaces to avoid the direct contact among the friction pairs more effectively, resulting in the improved anti-wear performances. Additionally, the addition of IF–WS2 particles effectively delayed the rise of lubricating oil temperature. In addition, dispersant span 80 can effectively improve the dispersion and stability of IF–WS2 in PAO6. This work provides us for understanding the effective lubrication mechanism of IF–WS2 particles in more detail and having a new acknowledge of the comprehensive performance of IF–WS2/PAO6 oil.