Walter Perrie

Dr. Walter Perrie


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2018 in Journal of Physics D: Applied Physics
Verified
Journal Article
Open access
PDF file
GZGuangyu Zhu
Guangyu Zhu
DWDavid J Whitehead
David J Whitehead
WPWalter Perrie
Walter Perrie
OAOlivier Jaques Allegre
Olivier Jaques Allegre
VOV Olle
V Olle
VVVojtech Volle
Vojtech Volle
Spatial light modulators (SLMs) addressed with computer generated holograms (CGHs) can create structured light fields on demand when an incident laser beam is diffracted by a phase CGH. The power handling limitations of these devices based on a liquid crystal layer has always been of some concern. With careful engineering of chip thermal management, we report the detailed optical phase and temperature response of a liquid cooled SLM exposed to picosecond laser powers up to 〈 P 〉 = 220 W at 1064 nm. This information is critical for determining device performance at high laser powers. SLM chip temperature rose linearly with incident laser exposure, increasing by only 5 °C at 〈 P 〉 = 220 W incident power, measured with a thermal imaging camera. Thermal response time with continuous exposure was 1–2 s. The optical phase response with incident power approaches 2 π radians with average power up to 〈 P 〉 = 130 W, hence the operational limit, while above this power, liquid crystal thickness variations limit phase response to just over π radians. Modelling of the thermal and phase response with exposure is also presented, supporting experimental observations well. These remarkable performance characteristics show that liquid crystal based SLM technology is highly robust when efficiently cooled. High speed, multi-beam plasmonic surface micro-structuring at a rate R = 8 cm 2 s −1 is achieved on polished metal surfaces at 〈 P 〉 = 25 W exposure while diffractive, multi-beam surface ablation with average power 〈 P 〉 =100 W on stainless steel is demonstrated with ablation rate of ~4 mm 3 min −1 . However, above 130 W, first order diffraction efficiency drops significantly in accord with the observed operational limit. Continuous exposure for a period of 45 min at a laser power of 〈 P 〉 = 160 W did not result in any detectable drop in diffraction efficiency, confirmed afterwards by the efficient parallel beam processing at 〈 P 〉 = 100 W. Hence, no permanent changes in SLM phase response characteristics have been detected. This research work will help to accelerate the use of liquid crystal spatial light modulators for both scientific and ultra high throughput laser-materials micro-structuring applications.

15 September 2010 in Applied Physics B
Verified
Journal Article
Closed access
PDF file
DLD. Liu
D. Liu
ZKZ. Kuang
Z. Kuang
WPWalter Perrie
Walter Perrie
Patricia ScullyPatricia Scully
Patricia Scully
ABA. Baum
A. Baum
KWK. G. Watkins
K. G. Watkins

1 October 2018 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
LCLie Chen
Lie Chen
XWXing Wang
Xing Wang
TYTao Yang
Tao Yang
HPHeng Ping
Heng Ping
PBPeter Bennett
Peter Bennett
DLDun Liu
Dun Liu
This paper demonstrates laser surface modification of silicone rubber using an economic and efficient nanosecond fibre laser. The resulting surface morphology shows that micro-nano structures leading to an increase in the surface slope were formed after processing. The effect of laser power on the surface wettability was investigated demonstrating that the contact angle of the silicone rubber surface increased with increasing laser fluence. The water contact angle on the treated surface reached ~160° with a rolling-off angle of ~3° when the laser fluence reached 10 J cm −2 . After laser processing, both the roughness and root mean square slope of the silicone rubber surface increased with increasing fluence and reached maximum at a fluence of 10 J cm −2 . An analysis of the pre- and post processing surfaces suggested there were no significant compositional changes, but there were some micro-structural changes to the polymer chain, namely, cleavage of the Si–O–Si bonds. It is thus proposed that the hierarchical micro-nano structures and hence the change in the root mean square slope of the silicone rubber surface induced by laser irradiation are the primary reasons for its superhydrophobicity. The preparation of superhydrophobic silicone rubber can have important applications in self-cleaning, anti-icing, and anti-pollution.

1 April 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
YTYue Tang
Yue Tang
WPWalter Perrie
Walter Perrie
DSDavid Rico Sierra
David Rico Sierra
QLQianliang Li
Qianliang Li
DLDun Liu
Dun Liu
GDGeoff Dearden
Geoff Dearden
Diffractive multi-beams based on 1 × 5 and 2 × 2 binary Dammann gratings applied to a spatial light modulator (SLM) combined with a nanostructured S-wave plate have been used to generate uniform multiple cylindrical vector beams with radial and azimuthal polarizations. The vector quality factor (concurrence) of the single vector vortex beam was found to be C = 0.95 ± 0.02, hence showing a high degree of vector purity. The multi-beams have been used to ablate polished metal samples (Ti-6Al-4V) with laser-induced periodic surface structures (LIPSS), which confirm the polarization states unambiguously. The measured ablation thresholds of the ring mode radial and azimuthal polarizations are close to those of a Gaussian mode when allowance is made for the expected absolute intensity distribution of a ring beam generated from a Gaussian. In addition, ring mode vortex beams with varying orbital angular momentum (OAM) exhibit the same ablation threshold on titanium alloy. Beam scanning with ring modes for surface LIPSS formation can increase micro-structuring throughput by optimizing fluence over a larger effective beam diameter. The comparison of each machined spot was analysed with a machine learning method—cosine similarity—which confirmed the degree of spatial uniformity achieved, reaching cosθ > 0.96 and 0.92 for the 1 × 5 and 2 × 2 arrays, respectively. Scanning electron microscopy (SEM), optical microscopy and white light surface profiling were used to characterize and quantify the effects of surface modification.

20 August 2020 in Journal of Physics D: Applied Physics
Verified
Journal Article
Open access
YTYue Tang
Yue Tang
WPWalter Perrie
Walter Perrie
JSJoerg Schille
Joerg Schille
ULUdo Loeschner
Udo Loeschner
QLQianliang Li
Qianliang Li
GDGeoff Dearden
Geoff Dearden
Cylindrical vector vortex (CVV) beams are topical forms of structured light, and have been studied extensively as single beams, non-separable in two degrees of freedom: spatial mode and polarisation. Here we create arrays of CVV beams using a combination of dynamic phase controlled Dammann gratings and spin–orbit coupling through azimuthally varying geometric phase. We demonstrate control over the number, geometry and vectorness of the CVV arrays by simple adjustment of waveplates and computer generated holograms. To quantify the efficacy of our approach, we employ a recently proposed vector quality factor analysis, realising high quality vector beam arrays with purities in excess of 95%. Our approach is scalable in array size, robust (no interferometric beam combination) and allows for the on-demand creation of arbitrary vector beam arrays, crucial for applications that require multi-spot arrays, for example, in fast laser materials processing, multi-channel communication with spatial modes, and holographic optical traps, as well as in fundamental studies with vector optical lattices.

1 December 2019 in Materials Research Express
Verified
Journal Article
Open access
PDF file
LCLie Chen
Lie Chen
HPHeng Ping
Heng Ping
TYTao Yang
Tao Yang
THTao Hu
Tao Hu
PBPeter Bennett
Peter Bennett
DLDun Liu
Dun Liu