Francis turbine guide vanes have pivoted support with external control mechanism, for conversion of pressure to kinetic energy and to direct them to runner vanes. This movement along the support is dependent on variation of load and flow (operating conditions). Small clearance gaps between facing plates and the upper and lower guide vane tips are available to aid this movement, through which leakage flow occurs. This secondary flow disturbs the main flow stream, resulting performance loss. Additionally, these increased horseshoe vortex, in presence of sand, when crosses through the gaps, both the surfaces are eroded. This causes further serious effect on performance and structural property by increasing gaps. This paper discusses the observation of the severity in hydropower plants and effect of clearance gaps on general performance of the Francis turbine through computational methods. It also relates the primary result with the empirical relation for leakage flow prediction. Additionally, a possible method to computationally estimate thickness depletion has also been presented. With increasing clearance gap, leakage increases, which lowers energy conversion and turbine efficiency along with larger secondary vortex.

This work reviews the current operational condition and activities on design modification for different applications of ejectors. Ejectors being a simple mechanical system capable of performing multiple fluid related functions (vacuum generation, pumping, mixing, condensing and heat exchanging), have been an essential part of several industrial processes. Two areas have been emphasized; internal flow and application-based modifications in components of ejectors. The geometry and inlet flow conditions were found to be the prime influencing factor of its performance. The objective and application-based modifications were performed on the primary nozzle, secondary nozzle, mixing chamber, throat and diffuser. The resultant performance was found to be dependent on operational condition and fluid type. This emphasizes the requirement of application-based design selection of the technology. In addition, the flow dynamics of condensing, non-condensing, particle and slurry flow has been studied based on available literatures. The one-point final objective is to identify the usability of primary water jet ejectors for active vapor transport and condensation, to replace vacuum pump and condenser in compact domestic water desalination system.

This study is focused on enhancing secondary vapor entrainment and direct-contact condensation in a water jet eductor for the purpose of developing a compact, medium-scale desalination system. It encompasses an extended investigation of an eductor as a condenser, or heat exchanger, for the entrained phase. Exergy study, experimental measurement, and computational analysis are the primary methodologies employed in this work. The target parameters of the optimization work were set through exergetic analysis to identify the region of maximum exergy destruction. In the case of water and water vapor as primary and secondary fluids, mixing and condensation initiates in the mixing chamber of the eductor and is where the maximum exergy destruction was calculated. Therefore, multi-jet primary nozzle eductors were studied to determine the effect of increased interphase interaction area on the exergy destruction and the maximum suction and cooling capacities. Increases in the entrainment ratio, condensation rate and heat transfer coefficient were noted for increasing numbers of nozzles when comparing one-, two- and three-jet eductors.

The expansion of the existing industries involved in the production of components of hydropower to the Francis turbine manufacturer up to 5 MW unit size has been recognized as one of the most promising business models in Nepal. Given the current fact that the development of Francis turbines with the manufacturers of Nepal has not been done yet, due to lack of designing expertise and limitations in the available technology, this paper presents the use of different available manufacturing technologies, which is suitable in the Nepalese hydropower market. This is an experience based paper, in which the advanced manufacturing process implementing Computer Aided Simulation (CAS), Computer Aided Design (CAD), and Computer Aided Manufacturing (CAM) is introduced for turbine manufacturing. Moreover, CAD from Solidworks, 3D printing from Rapid Prototyping Machine (RPM), and manufacturing of three designs by three different methods, dye casting, lost wax casting, and forging in a local workshop, have been described. The outcome of this work is the identification of suitable Francis turbine development methodologies in context of Nepal, incorporating industrial revolution through research based products.

This is an experimental work performed to identify the influence of direct contact condensation inside an eductor. The fluid used in the experiments is water in two different phases: liquid and vapor, for primary and secondary flows, respectively. This study was conducted in an attempt to establish the suitability of an eductor as a combined vacuum generator and condenser for membrane desalination applications. The pressure and temperature measurements at critical points in the flow paths have been summarized to identify the influence of primary flow on secondary fluid saturation and condensation. In addition, the mechanism of phase change has been explained through the photography of fluid flow in a two-dimensional eductor. A consistent oscillation of the gas-liquid interface was observed during steady-state operations of the eductor. This work also contributes to the validation of future computational research. It will provide a baseline for computational thermal fluid analysis related to the mixing of condensing and non-condensing flow. In general, the research encompasses the practical operational scenario and provides information on the heat and mass transfer of direct contact condensation with a finite secondary source.