Division of Combustion Technology and Internal Combustion Engines, Institute of Thermal Technology, Silesian University of Technology, 44-100 Gliwice, Poland
Dr. Andrzej Szlék
Division of Combustion Technology and Internal Combustion Engines, Institute of Thermal Technology, Silesian University of Technology, 44-100 Gliwice, Poland
This research considers a preliminary comparative technical evaluation of two micro-gas turbine (MGT) systems in combined heat and power (CHP) mode (100 kWe), aimed at supplying heat to a residential community of 15 average-sized buildings located in Central Europe over a year. Two systems were modelled in Ebsilon 15 software: a natural gas case (benchmark) and an ammonia-fueled case, both based on the same on-design parameters. Off-design simulations evaluated performance over variable ambient temperatures and loads. Idealized, unrecuperated cycles were adopted to isolate the thermodynamic impact of the fuel switch under complete combustion assumption. Under these assumptions, the study shows that the ammonia system produces more electrical energy and less excess heat, yielding marginally higher electrical efficiency and EUF (26.05% and 77.63%) than the natural gas system (24.59% and 77.55%), highlighting ammonia’s utilization potential in such a context. Future research should target validating ammonia combustion and emission profiles across the turbine load range, and updating the thermodynamic model with a recuperator and SCR accounting for realistic pressure losses.
This paper develops a novel coupled model to predict the thermal behavior of a high-temperature fast heat storage unit, integrating Power-to-Heat technology with steam generation. A phase change material (PCM) made of a ZnAl6 metal alloy is used for heat storage. Electricity is used to charge the battery, and the stored energy is used to produce superheated steam during discharge. The coupled model was based on a 3D multiphase CFD model of the heat storage unit and a 1D multiphase water boiling model implemented in Python language. The CFD model solves the transient conservation equations of mass, momentum, and energy using the enthalpy–porosity method to describe phase change, while heat transfer to water is represented by a coupled 1D boiling model. The paper also presents a preliminary design, a computational strategy, and boundary conditions for the operating modes, providing an analytical foundation for detailed engineering, production, and implementation in real-world industrial environments. The presented results confirmed the correct operation of the model and enabled the evaluation of system performance, discharge behavior, and validation of the geometric assumptions required to achieve the target steam parameters. The proposed modular design allows for system scalability, while the entire system is a response to the daily variability of electricity prices resulting from periodic reductions in demand and overproduction of electricity from renewable sources. Estimated thermal behavior of the thermal storage unit for the discharging scenario allows reaching constant output power at the level of 200 kW for 85 min. Integration with a cooling reduction station allows constant system power output to be maintained by increasing the mass flow rate as the steam parameters decrease from over 400 °C to 200 °C with a lowering state of charge.
Biomass combustion in small-scale boilers in Eastern Europe has recently become a very popular heating option. Biomass boilers are gradually replacing old, coal-fired installations, especially in the domestic sector. In comparison with coal, biomass contains more phosphorus, chlorine, and potassium, which may cause the corrosion, slagging, and fouling of heating surfaces inside the combustion chamber. Such problems may be reduced by properly controlling the combustion process, as well as adding substances like halloysite to the fuel. This paper presents the results of adding halloysite to wood pellets made of coniferous wood, rape straw, and wood/rape blend in the combustion process of a 25 kW retort boiler. The results demonstrate that adding halloysite to biomass increases the ash sintering temperature, which may, in turn, reduce slagging. The addition of halloysite also reduces the KCl concentration in the ash and the total solid compounds, potentially lowering the risk of corrosion in the boiler. A slight reduction in CO, OGC, and SO2 concentrations was observed for rape straw biomass pellets with the halloysite addition. Moreover, the experimental results indicate that the addition of halloysite to fuel may influence boiler efficiency, especially during the combustion process of agricultural biomass and its blends.
1 August 2006 in Combustion Science and Technology
Urban tree-management operations generate substantial amounts of woody biomass that often remain underutilized despite their potential value as a local renewable fuel. This study investigates the possibility of using woodchips and sawdust delivered from municipal tree-cutting activities as boiler fuel, with a specific focus on how fuel moisture, particle size, and natural-fiber packaging influence combustion performance and emission characteristics. In collaboration with a municipal greenery-cutting company, representative batches of biomass were collected, characterized through proximate and ultimate analyses, and combusted in a small-scale boiler. Unlike conventional densification routes (pelletization/briquetting), the proposed approach uses combustible natural-fiber packaging to create modular ‘macro-pellets’ from minimally processed urban residues. The study quantifies how this low-energy packaging concept affects emissions and boiler efficiency relative to loose chips/sawdust at two moisture levels. The results demonstrate that packaging the fuel in jute bags markedly improved performance for both woodchips and sawdust by stabilizing the fuel bed, enhancing air distribution, and reducing emissions of incomplete combustion products. Boiler efficiency increased from approximately 60% for raw unpackaged fuels to 71–75% for the dried and jute-packaged variants. The findings highlight that simple preprocessing steps—drying and packaging in natural-fiber bags—can substantially enhance the energy recovery potential of urban green waste, offering a practical pathway for integrating municipal biomass residues into a sustainable fuel.