1Cr11Ni2W2MoV is a new martensitic heat-resistant stainless steel utilized in the manufacturing of aero-engine high-temperature bearing components. Welding of this type of steel using fusion welding techniques causes many defects. Friction stir welding (FSW) is a valuable alternative. However, few investigations have been performed on the FSW of steels because of the high melting point and the costly tools. Numerical simulation in this regard is a cost-effective solution for the FSW of this steel in order to optimize the parameters and to reduce the number of experiments for obtaining high-quality joints. In this study, a 3D thermo-mechanical finite element model based on the Coupled Eulerian Lagrangian (CEL) approach was developed to study the FSW of 1Cr11Ni2W2MoV steel. Numerical results of metallurgical zones’ shape and weld appearance at different tool rotation rates of 250, 350, 450 and 550 rpm are in good agreement with the experimental results. The results revealed that the peak temperature, plastic strain, surface roughness and flash size increased with an increase in the tool rotation rate. Lack-of-fill defect was produced at the highest tool rotation rate of 650 rpm. Moreover, an asymmetrical stir zone was produced at a high tool rotation rate.

Lifetime is a basic support for the thermal insulation function of thermal barrier coatings (TBCs). Therefore, extending the life span is essential to develop next-generation TBCs. For this objective, the columnar structure formed by vertical cracks appears to make sense. However, the underlying mechanism is still unclear. This work scrutinizes the influence of periodic vertical cracks on cracking behavior in order to tailor high strain tolerant TBCs. A finite element model was evolved to explore the crack behavior influenced by thermal mismatch strain between substrate and coating. The virtual crack closure technique (VCCT) was used to describe the propagation of crack under load. It is found clearly that the space between two vertical cracks (short for SVC) along the in-plane direction has a noteworthy influence on the strain tolerance of TBCs. Results indicate that the strain energy release rate (SERR) and stresses at the pre-crack tip increase continuously with the increase of the SVC, suggesting that the driving force for cracks is increasing. The crack is not propagated when the SVC is very small, whereas the crack grows continuously with the increase of the SVC. The growth of a crack can be prevented by reducing the SVC. A critical value for the SVC was found. When the SVC is less than the critical value, the SERR can be dramatically reduced. Thus, the SVC of periodic cracks can be tailored to obtain TBCs with high strain tolerance.

Friction stir welding (FSW) is a leading technique for joining high-strength steel. This study investigates the relationship between weld power, heat generation (HG), cooling medium, and parent austenite grain (PAG) size during both FSW and submerged FSW (SFSW) processes on 11Cr-1.6W-1.6Ni Martensitic Stainless Steel. Weld power and HG were determined by measuring plunge force and tool torque at various tool rotation rates (350–550 rpm). Additionally, the PAG size and microstructural phases in the base metal (BM), thermo-mechanically affected zone (TMAZ), and stir zone (SZ) were examined using scanning electron microscopy (SEM), electron backscattered diffraction (EBSD), and X-ray diffraction (XRD). The results indicated that the SFSW of martensitic steel required a plunge force twice that of the FSW process, along with greater weld power. The heat generated during SFSW was 130% higher than in FSW at 550 rpm. Despite this, the peak temperatures in the SZ were lower in SFSW as a result of the surrounding water’s high heat absorption. This difference in thermal behavior significantly affected the microstructure. While FSW resulted in a complete phase transformation to fine PAG, SFSW showed only minimal or partial transformation and a higher strain rate. Consequently, the SZ and TMAZ in SFSW exhibited a higher hardness than in FSW.

As a solid-state welding technique, friction stir welding (FSW) has many advantages over conventional fusion welding. Its applications in the manufacturing and joining of parts in aerospace, automotive, and shipbuilding have significantly increased. Friction heat generation is the fundamental driver of the FSW process. It governs material flow, microstructural evolution, mechanical properties, and residual stresses. Understanding the effect of heat generated on the joint quality is essential for process parameter optimization, ensuring defect-free welds and high-quality joints. Thus, evaluating the thermal history of the FSW process is a key requirement for effective analysis. This comprehensive review critically discusses research studies published over the past three decades (1991–2025) that have examined different approaches to predict and measure heat generation in FSW. A total of 136 highly relevant articles were selected from the Scopus database and systematically analyzed. The effects of various welding parameters on heat generation, microstructural evolution, and joints’ mechanical properties have been reported. Different heat generation prediction and measurement techniques, such as analytical models, finite element models (FEM), and experimental methods have been discussed in terms of their feasibility, accuracy, advantages, disadvantages, and cost. The evolution, state of the art of analytical models and FEM over the last three decades are analyzed and future research directions are outlined. Finally, the correlation between process parameters, heat generated, microstructural development, and mechanical performance of the welded joints for various workpiece materials is investigated. This review provides a critical and comparative perspective that highlights the strengths and limitations of each method, offering practical guidance for researchers and industry practitioners.