This paper presents the impact of selected essential aspects of geological structure on the state of slope stability as assessed by changes in the safety factor (SF). The engineering geological slope features that were analysed include: (i) changes in soil cohesion and internal friction angle, (ii) presence of a weak soil layer and its span, (iii) structural discontinuity (i.e. fault), (iv) soil permeability properties and water conditions (i.e. groundwater level, long and heavy rainfall). A certain scheme of slope stability calculations has been proposed for a case involving complex geological conditions. The numerical modelling of a hypothetic slope was performed using the shear strength reduction method based on the finite element method.

The characteristics of peat’s are crucial for understanding natural processes and their suitable shaping through the management of water relations. This study focused on the results of one of the first hydraulic conductivity (k) laboratory tests of exemplary peat samples from the Biebrza Valley (a peatland of very high environmental importance) in relation to the stress state and hydraulic gradient. Further, the research was devoted to a specific test procedure of peat permeability as a key feature for landform development in wetlands. Detailed tests of dark brown/black samples were selected as the reference for the research investigations. Four long-term test series of water permeability were performed in a modified triaxial compression apparatus. In all selected hydraulic gradient variants (i = 5,10,25,40,55,85), the k values decreased from 6 × 10⁻⁸ m/s to 1.6 × 10⁻¹⁰ m/s with a stepwise increase in the effective confining pressures tested (10, 15, 30, 45, and 90 kPa). These results were related to the inherent soil features—a relatively high peat decomposition and external driver—confining pressure (radial stress) magnitude. Compared to the other Polish peat tests, the determined k values were at the lower end of their hydraulic conductivity range. The analysed organic soil is not a typical aquifer. Despite very high porosities (~88%) and a high organic matter content (81.1–89.4%) which is favourable for water accumulation, the characterized peat showed relatively low hydraulic conductivity values. Thus, this specific soil may differentiate the groundwater flow as it complicates strong contact with surface water.

Soil creep deformation refers to phenomena which take place in many areas and research in this field of science is rich and constantly developing. The article presents an analysis of the literature on soil creep phenomena. In light of the complexity of the issues involved and the wide variety of perspectives taken, this attempt at systematization seeks to provide a reliable review of current theories and practical approaches concerning creep deformation. The paper deals with subjects such as definition of creep, creep genesis, basic description of soil creep dynamics deformation, estimation of creep capabilities, various fields of creep occurrence, and an introduction to creep modeling. Furthermore, based on this analysis, a new direction for research is proposed.

The article shows the results of geophysical surveys performed by using Electrical Resistivity Tomography (ERT) method on selected region of Płock slope of a Tumski hill near Basilica of Assumption of the Blessed Virgin Mary in Płock and in Maszewo by the Vistula River a few kilometers north of Płock. The above-mentioned sections were selected due to landslide phenomena observed there. Geophysical surveys were conducted in order to verify the state of the distribution of electrical resistivity in the sectors where mass movement was identified. The electrofusion cross-section near Cathedral Basilica shows clays and sands. Also in ERT prospection a zone of loose soils with high resistance is clearly visible. The results of the ERT method from Maszewo, indicates historical land surface of a landslide and that the slope in Maszewo consists of cohesive deposits. In order to describe these particular issues, geological cross-sections and safety factor obtained by calculation are presented for the analyzed parts of the slope. The safety factor shows that probability of landslide activity near Cathedral Basilica is very unlikely and in Maszewo is very high

This study concerns the creep impact on strength parameters of the selected very cohesive soils (PI = 30–70%). The analysis refers to Neogene clays characterized by a complex structure, resulting directly from a complicated load history in the geological time scale and identified glacitectonic deformations. In the process of samples’ preparation for strength tests as well as during the interpretation of the post-failure state, particular attention was paid to the soil structure. The imaging methods (X-ray densitometry and computer microtomography) enabled the comparison of the soil structure and the selection of samples with similar characteristics. The completed program of strength tests consisted of two series of tests in the triaxial stress state, differentiated by the occurrence of the initial creep stage, preceding the typical strength test scheme under undrained conditions. This study allowed to obtain a quantitative assessment of the influence of the creep process on the strength parameters of tested soils. Constant stress lower than 60% of the shear stress deviator leads to the deceleration creep course (m parameter 0.64–0.89). As a result, higher values of internal friction angle (20% increase comparing to triaxial tests without creep stage) and cohesion reduction are obtained from triaxial creep tests. Creep parameter m is found to be a valuable indicator for differentiation of landslide activity trend. The tests proved low values of axial strains (1–5%) at failure, which was associated with lithogenesis. By the implementation of obtained strength parameters into the 3D finite element model of the slope, the potential influence of the creep process on the stability of an exemplary cross section of the Warsaw slope could be determined.

The study employs numerical calculations in the characterization of reservoir sandstone samples based on high-resolution X-ray computed microtomography. The major goals were to determine porosity through pore size distribution, permeability characterization through pressure field, and structure impact on rock strength by simulation of a uniaxial compression test. Two Miocene samples were taken from well S-3, located in the eastern part of the Carpathian Foredeep. Due to the relation between sample size and image resolution, two X-ray irradiation series with two different sample sizes were performed. In the first approach, the voxel side was 27 μm and in the second it was up to 2 μm. Two samples from different depths have been studied here. Sample 1 has petrophysical features of conventional reservoir deposits, in contrast to sample 2. The approximate grain size of sample 1 is in the range 0.1-1.0 mm, whereas for sample 2 it is 0.01-0.1 mm with clear sedimentation lamination and heterogenic structure. The porosity, as determined by μCT, of sample 1 is twice (10.3%) that of sample 2 (5.3%). The equivalent diameter of a majority of pores is less than 0.027 mm and their pore size distribution is unimodal right-hand asymmetrical in the case of both samples. In relation to numerical permeability tests, the flow paths are in the few privileged directions where the pressure is uniformly decreasing. Nevertheless, there are visible connections in sample 1, as is confirmed by the homogenous distribution of particles in the pore space of the sample and demonstrated in the particle flow simulations. The estimated permeability of the first sample is approximately four times higher than that of the second one. The uniaxial compression test demonstrated the huge impact of even minimal heterogeneity of samples in terms of micropores: 4-5 times loss of strength compared to the undisturbed sample. The procedure presented shows the promising combination of microstructural analysis and numerical simulations. More specific calculations of lab tests with analysis of variable boundary conditions should be performed in the future.