Francesco Musiari

Prof. Francesco Musiari

Università di Parma
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2020 in International Journal of Adhesion and Adhesives
Verified
Journal Article
Closed access
Fabrizio MoroniFabrizio Moroni
Fabrizio Moroni
Francesco MusiariFrancesco Musiari
Francesco Musiari
CSCorrado sciancalepore
Corrado sciancalepore
Massimo MessoriMassimo Messori
Massimo Messori

22 November 2023 in The Journal of Adhesion
Verified
Journal Article
Closed access
Francesco MusiariFrancesco Musiari
Francesco Musiari
Fabrizio MoroniFabrizio Moroni
Fabrizio Moroni
ALAdrian Hugh Alexander Lutey
Adrian Hugh Alexander Lutey

20 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Francesco MusiariFrancesco Musiari
Francesco Musiari
Fabrizio MoroniFabrizio Moroni
Fabrizio Moroni
The low quality of adhesion performance on polymeric surfaces has forced the development of specific pretreatments able to toughen the interface between substrate and adhesive. Among these methods, atmospheric pressure plasma treatment (APPT) appears particularly suitable for its environmental compatibility and its effectiveness in altering the chemical state of the surface. In this work, an experimental study on adhesively bonded joints realized using polyamide as substrates and polyurethane as the structural adhesive was carried out with the intent to characterize their fatigue behavior, which represents a key issue of such joints during their working life. The single lap joint (SLJ) geometry was chosen and several surface pretreatments were compared with each other: degreasing, abrasion (alone and followed by APPT) and finally APPT. The results show that the abrasion combined with APPT presents the most promising behavior, which appears consistent with the higher percentage of life spent for crack propagation found by means of DIC on this class of joints with respect to the others. APPT alone confers a good fatigue resistance with respect to the simple abrasion, especially at a low number of cycles to failure.

20 November 2018 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
FMF Moroni
F Moroni
Francesco MusiariFrancesco Musiari
Francesco Musiari
Alessandro PirondiAlessandro Pirondi
Alessandro Pirondi
The state of the surface plays a crucial role in defining the mechanical properties of bonded joints, in particular, the chemical state of the adherend surface and its structural morphology have been proved to be the main elements of the bonding process. The structural morphology of the surface strictly depends from its topological features, like roughness, presence and distribution of grooves, homogeneity, etc. In a previous work, the effect provided by pulsed Yb-laser ablation on the mode I energy release rate of aluminium double cantilever beam joints was evaluated, in order to identify a relation between the combination of laser parameters and the morphological characteristics of the ablated surfaces which can support in identifying the optimal process configuration. The experimental tests showed that the fracture toughness of the double cantilever beam joints grew up as the surface roughness increased until a threshold value, after which the grooves resulted too narrow to allow the adhesive to completely fill them, inducing a higher amount of entrapped air into the grooves and therefore reducing the level of failure propagation energy. In this work, the problem dealing with the influence that the presence of air bubbles has over the mechanical behaviour of bonded joints was considered and the study went deeper into the investigation on the relation between laser-induced surface topology and mechanical response of joints. Different surface textures involving different directions and conditions of treatment were realized and their effect on the mechanical properties of aluminium bonded specimens was evaluated through experimental tests. The characterization of the treated surfaces was carried out by observing them with a 3D optical profiler and with SEM analysis and by measuring some geometrical features of the patterns created as a result of laser ablation.

7 October 2023 in Journal of Food Engineering
Verified
Journal Article
Open access
Francesco MusiariFrancesco Musiari
Francesco Musiari
FMFabrizio Moroni
Fabrizio Moroni
Alessandro PirondiAlessandro Pirondi
Alessandro Pirondi
CFClaudio Favi
Claudio Favi

5 February 2025 in Adhesives
Verified
Journal Article
Open access
PDF file
Mattia FrascioMattia Frascio
Mattia Frascio
SMStefano Morchio
Stefano Morchio
Francesco MusiariFrancesco Musiari
Francesco Musiari
MKMuhammad Usman Khalid
Muhammad Usman Khalid
FDFederico Dittamo
Federico Dittamo
Massimiliano AvalleMassimiliano Avalle
Massimiliano Avalle
Additive manufacturing enables new design solutions across various engineering fields. This work presents a method to enhance the sustainability of adhesive joints by designing joints that can be disassembled and repaired multiple times. The approach involves the use of a Multi-Material Additive Manufacturing process to produce substrates with integrated circuits and electrical resistance, printed using a conductive filament. This resistance can be used to heat the thermoplastic adhesive layer up to 110 °C, allowing for reversibility in the assembly process and enabling joint re-use and repair without constraints on the component’s materials and thicknesses. The joints tested after successive assembly/disassembly operations reach maximum strength during the first iteration, which decreases by around 50% after five repair iterations. The focus of the work is on the feasibility of this process, but it is expected that performance can be improved after process optimization. This result could be highly valuable for enabling component in-service healing and the design for demanufacturing and remanufacturing.