Single point incremental forming (SPIF) has been demonstrated to accomplish current trends and requirements in industry. Recent studies have applied this technology to hole-flanging by performing different forming strategies using one or multiple stages. In this work, an optimization procedure is proposed to balance fabrication time and thickness distribution along the produced flange in a two-stage variant. A detailed analytical, numerical and experimental investigation is carried out to provide, evaluate and corroborate the optimal strategy. The methodology begins by analysing the single-stage process to understand the deformation and failure mechanisms. Accordingly, a parametric two-stage SPIF strategy is proposed and evaluated by an explicit Finite Element Analysis to find the optimal parameters. The study is focused on AA7075-O sheets with different pre-cut hole diameters and considering a variety of forming tool radii. The study exposes the relevant role of the tool radius in finding the optimal hole-flanging process by the proposed two-stage SPIF.
29 May 2024 in International Journal of Mechanical Sciences
Recently, the research interest of hole-flanging has turned from conventional press-working to single-point incremental forming (SPIF) as a viable process for small- and medium-sized batches. Both technologies have been studied separately using different approaches and, therefore, most studies cannot be easily compared. Besides, some studies that measured the formability in SPIF using the classical limiting forming ratio (LFR) showed conflicting results that still need to be clarified. Under these circumstances, the aim of this work is to provide a better understanding of the deformation process and the material formability in hole-flanging by critically comparing both forming processes. To this end, a series of experimental tests on AA7075-O sheet of 1.6-mm thickness by press-working and single-stage SPIF, using forming tools with different profile radii, are analyzed. The material formability and flange geometry are compared and discussed in detail. The process limits are analyzed by using both the Forming Limit Diagram (FLD) and the LFR. The failure modes by necking and fracture are clearly identified and assessed on both processes along with the influence of the bending induced by the tools during the flange forming. Results conclude that the LFR is not an adequate parameter to compare formability between processes other than press-working and, accordingly, two additional variables based on either the flange height or the average thickness reduction are proposed to successfully analyze flangeability.
The experimental detection of localized necking is an important issue in sheet metal forming. Today, the most common and extended techniques are strain-based methods using digital image correlation (DIC). The present work discuses a thermal methodology to detect the onset of necking in metals based on the analysis of the temperature gradient using digital infrared thermography (DIT). A series of tensile tests of H240LA-O3 high-strength steel of 1.2mm thickness is analysed using DIC and DIT techniques. It is proposed that necking initiates when the temperature difference at a reference distance from the necking point reaches a critical value, which allows identifying the necking time and estimating the limit strains from the visible images using circle grid analysis.
2 October 2023 in Advances in Science and Technology
The Forming Limit Curve (FLC) shows the limit combinations of principal strains on the sheet surface that can be successfully achieved before necking appears. Above the FLC, Atkins in 1996 proposed the existence of an unstable region where localized necking develops before reaching at the Fracture Forming Limit (FFL). Only the methodology for the evaluation of the FLC is covered in an international standard ISO 12004-2, where the basis of the tests consists of stretching of a previously clamped sheet blank over a Marciniak or Nakazima punch, providing an almost linear strain path in the sheet surface of the specimen. On the contrary, in single-point incremental forming (SPIF) processes, the hemispherical-shaped tools usually employed are relatively small compared to the general dimension of the specimen, producing a highly nonlinear strain path derived from both the incremental nature of the process and the severe curvature imposed by the small radii of the punches used in the forming process.Many authors have observed fracture strains in SPIFed samples well above the FFL obtained with Nakazima tests under the ISO 12004-2 standard. At the macroscopic level, the reason for this behaviour has been explained mainly based on the effect of bending and the difference in the stress triaxiality level, among others. This research analyzes the initiation of ductile fracture in Nakazima and SPIF specimens under a scanning electron microscope to elucidate the reasons of those differences at the microscopic level.
Flanges are commonly used in aircrafts to provide stiffness and support for the assembly Incremental Sheet Forming (ISF) processes have been approached to produce both stretch and shrink flanges as a low-cost alternative in the fabrication of a small number of parts and prototypes. This work analyzes stretch and shrink flanges of AA2024-T3 sheet with different geometries manufactured by Single Point Incremental Forming (SPIF). The numerical simulation using Finite Elements of the flanges allows evaluating the stress in successful and failed flanges. On the one hand, the formability of stretch flanges is usually evaluated in terms of principal strains within the Forming Limit Diagram (FLD). However, this approach does not seem to capture all the physics to explain the enhancement in formability observed in SPIF over the conventional forming. A formability analysis is performed in the field of stress triaxiality versus equivalent plastic strain, discussing the differences between successful and fractured specimens. On the other hand, for shrink flanging, the appearance of wrinkles is analyzed in terms of the compressive stresses along the flange during the incremental forming. This allows to determine a critical limit stress of winkling to predict the failure in practice for a given geometry and forming condition.