Thin-walled elements are widely used in the aerospace industry, where the aim is to reduce the process time and the weight of the structure while ensuring the sufficient quality of the finished product. Quality is determined by geometric structure parameters and dimensional and shape accuracy. The main problem encountered during the milling of thin-walled elements is the deformation of the product. Despite the various methods available for measuring deformation, more are still being developed. This paper presents selected surface topography parameters and deformation of vertical thin-walled elements during an experiment under controlled cutting conditions for samples from titanium alloy Ti6Al4V. Constant parameters of feed (f), cutting speed (V_c,) and tool diameter (D) were used. Samples were milled using a tool for general-purpose and a tool for high-performance machining, as well as two different machining approaches: with greater involvement of face milling, and cylindrical milling with a constant material removal rate (MRR). For samples with vertical thin walls, the parameters of waviness (W_a, W_z,) and roughness (R_a, R_z) were measured using a contact profilometer in the selected areas on both processed sides. Deformations were determined in selected cross-sections perpendicular and parallel to the bottom of the sample using GOM measurement (GOM—Global Optical Measurement). The experiment showed the possibility of measuring deformations and deflection arrows of thin-walled elements proceeded from titanium alloy using GOM measurement. Differences in selected surface topography parameters and deformations were observed for the machining methods used with an increased cross-section of the cut layer. A sample with a deviation of 0.08 mm from the assumed shape was obtained.

Surface quality has always been an important goal in the manufacturing industry, as it is not only related to the achievement of appropriate geometrical tolerances but also plays an important role in the tribological behavior of the surface as well as its resistance to fatigue and corrosion. Usually, in order to achieve sufficiently high surface quality, process parameters, such as cutting speed and feed, are regulated or special types of cutting tools are used. In the present work, an alternative strategy for slot milling is adopted, namely, trochoidal milling, which employs a more complex trajectory for the cutting tool. Two series of experiments were initially conducted with traditional and trochoidal milling under various feed and cutting speed values in order to evaluate the capabilities of trochoidal milling. The findings showed a clear difference between the two milling strategies, and it was shown that the trochoidal milling strategy is able to provide superior surface quality when the appropriate process parameters are also chosen. Finally, the effect of the depth of cut, coolant and trochoidal stepover on surface roughness during trochoidal milling was also investigated, and it was found that lower depths of cut, the use of coolant and low values of trochoidal stepover can lead to a considerable decrease in surface roughness.

The main functions of thin-walled structures—widely used in several industries—are to reduce the weight of the finished product and to increase the rigidity of the structure. A popular method for machining such components, often with complex shapes, is using milling. However, milling involves undesirable phenomena. One of them is the occurrence of vibrations caused by the operation of moving parts. Vibrations strongly affect surface quality and also have a significant impact on tool wear. Cutting parameters, machining strategies and tools used in milling constitute some of the factors that influence the occurrence of vibrations. An additional difficulty in milling thin-walled structures is the reduced rigidity of the workpiece—which also affects vibration during machining. We have compared the vibration signal for different approaches to machining thin-walled components with vertical walls made of Ti6Al4V titanium alloy and Inconel 625 nickel alloy. A general-purpose cutting tool for machining any type of material was used along with tools for high-performance machining and high-speed machining adapted for titanium and nickel alloys. A comparison of results was made for a constant material removal rate. The Short-Time Fourier Transform (STFT) method provided the acceleration vibration spectrograms for individual samples.

Titanium and nickel alloys are used in the creation of components exposed to harsh and variable operating conditions. Such components include thin-walled structures with a variety of shapes created using milling. The driving factors behind the use of thin-walled components include the desire to reduce the weight of the structures and reduce the costs, which can sometimes be achieved by reducing the machining time. This situation necessitates, among other things, the use of new machining methods and/or better machining parameters. The available tools, geometrically designed for different strategies, allow working with similar and improved cutting parameters (increased cutting speeds or higher feed rates) without jeopardizing the necessary quality of finished products. This approach causes undesirable phenomena, such as the appearance of vibrations during machining, which adversely affect the surface quality including the surface roughness. A search is underway for cutting parameters that will minimize the vibration while meeting the quality requirements. Therefore, researching and evaluating the impact of cutting conditions are justified and common in scientific studies. In our work, we have focused on the quality characteristics of horizontal thin-walled structures from Ti₆Al₄V titanium alloys obtained in the milling process. Our experiments were conducted under controlled cutting conditions at a constant value of the material removal rate (2.03 cm³⁄min), while an increased value of the cut layer was used and tested for use in finishing machining. We used three different cutting tools, namely, one for general purpose machining, one for high-performance machining, and one for high-speed machining. Two strategies were adopted: adaptive face milling and adaptive cylindrical milling. The output quantities included the results of acceleration vibration amplitudes, and selected surface topography parameters of waviness (W_a and W_z) and roughness (R_a and R_z). The lowest values of the pertinent quantities were found for a sample machined with a high-performance tool using adaptive face milling. Surfaces typical of chatter vibrations were seen for all samples.

Thin-walled structures are used in many industries. The need to use such elements is dictated by the desire to reduce the weight of the finished product, as well as to reduce its cost. The most common method of machining such elements is the use of milling, which makes it possible to make a product of almost any shape. However, several undesirable phenomena occur during the milling of thin-walled structures. The main phenomenon is a deformation of the thin wall resulting from its reduced stiffness. Therefore, it is necessary to control the dimensional and shape accuracy of finished products, which is carried out using various measuring instruments. The development of newer measuring methods such as optical methods is being observed. One of the newer measuring machines is the 3D optical scanner. In the present experiment, thin-walled samples in horizontal orientation of Ti6Al4V titanium alloy were machined under controlled cutting conditions. During machining, the cutting speed and feed rate were assumed constant, while the input factors were the tool and cutting strategy. This paper presents graphs of deviations in the determined cross-section planes of thin-walled structures using a 3D optical scanner and a coordinate measuring machine. A correlation was made between the results obtained from the measurement by the optical method and those determined by the contact method. A maximum discrepancy of about 8% was observed between the methods used.

During the production of components, manufacturers of structures are obliged to meet certain requirements and ensure appropriate quality characteristics. It is especially important during the manufacturing of thin-walled structures, which are subject to many errors during machining due to the reduced rigidity of the products, including the deformation of thin walls, which may be the result of the vibration of the system. The appearance of vibrations reduces the quality of the machined surface affecting the increase in the values of surface topography parameters—waviness and roughness. Thin-wall structures—titanium or nickel alloy, among others—play a key role in the aerospace industry, which constantly strives to reduce the weight of the entire structure while meeting requirements. The present work focuses on the evaluation of the parameters of surface topography, dimensional and shape accuracy during the milling of nickel alloy Inconel 625 samples containing a thin wall in a vertical orientation. The experiment was conducted under controlled cutting conditions using a constant material removal rate. As part of the surface topography section, the distribution of waviness, Wa and Wz, and roughness, Ra and Rz, was determined in selected measurement areas in the direction parallel to the direction of the feed motion. Dimensional deviations, measured with a 3D optical scanner, were determined in selected cross sections in the direction perpendicular and parallel to the bottom of the sample presenting the deflection of the thin-walled structure. The results provide information that the used parameter sets affect the measured quantities to varying degrees.