Raw short wood fibres generally showed better mechanical performance than long ones. Alkaline treatment did not improve the mechanical properties of the composites after reactive extrusion and injection moulding.
Exploring new construction materials with low environmental impact leads to innovation in buildings and also to the expansion of environmental sustainability in the construction industry. In this perspective, the thermal insulation and the sound absorption performances of Buriti (Mauritia flexuosa) foam were analyzed for potential application in buildings. This material is of plant origin, it is natural, renewable, abundant, and has a low environmental impact. In this research, characterizations were made by scanning electron microscopy (SEM), apparent density, thermogravimetry (TGA and DTG), thermal conductivity, and sound absorption. The SEM analysis revealed a predominantly porous, small, and closed-cell morphology in the vegetable foam. Due to its porosity and lightness, the material has an apparent density similar to other thermal insulating and sound-absorbing materials used commercially. The evaluation of thermogravimetric (TGA/DTG) results demonstrated thermal stability at temperatures that attest to the use of Buriti foam as a building material. Based on the thermal conductivity test, the Buriti foam was characterized as an insulating material comparable to conventional thermal insulation materials and in the same range as other existing thermal insulators of plant origin. Concerning sound absorption, the Buriti foam presented a low performance in the analyzed frequency range, mainly attributed to the absence of open porosity in the material. Therefore, understanding the sound absorption mechanisms of Buriti foam requires further studies exploring additional ways of processing the material.
Wood plastic composites (WPCs) offer a means to reduce the carbon footprint by incorporating natural fibers to enhance the mechanical properties. However, there is limited information on the mechanical properties of these materials under hostile conditions. This study evaluated composites of polypropylene (PP), polystyrene (PS), and polylactic acid (PLA) processed via extrusion and injection molding. Tests were conducted on tensile and flexural strength and modulus, heat deflection temperature (HDT), and creep analysis under varying relative humidity conditions (10% and 90%) and water immersion, followed by freeze—thaw cycles. The addition of fibers generally improved the mechanical properties but increased water absorption. HDT and creep were dependent on the crystallinity of the composites. PLA and PS demonstrated a superior overall performance, except for their impact properties, where PP was slightly better than PLA.
Polymeric syntactic foams are composites made from the mixture of Hollow Glass Microspheres (HGM) and polymer matrices. One of their main characteristics is their low density and the production of these composites using a matrix derived from renewable sources potentiates their development without neglecting sustainability. In this paper , the properties of High Density Polyethylene (HDPE)/HGM syntactic foams containing 1% and 5% w/w HGM and 5% w/w of a compatibilizer are assessed. The composites were prepared by two processing routes: single screw extruder and twin screw extruder. The morphology and mechanical properties (tensile and impact) of the syntactic foams thus manufactured were ascertained. Morphological analysis indicated that matrix/filler adhesion was poor for all samples and that the best HGM dispersions were obtained in twin screw extruded samples. Mechanical properties were affected by the processing route adopted and by the content of hollow glass microspheres added. Elastic modulus, tensile strength and strain were reduced by 20, 10 and 23%, respectively, in systems processed in a twin screw extruder. Impact strength was the exception, with an increase of more than 300%. Higher contents of hollow glass microspheres led to reductions in mechanical strength of the syntactic foams, varying from 5% for the elastic modulus to 50% for strain.
The current study focused on improving the properties of polylactic acid (PLA) for wider application in load‐bearing scenarios. Various methods were explored to optimize the interaction between PLA and natural fibers, particularly wood fibers (WFs). Alkalized and epoxy‐impregnated WFs were evaluated against untreated WFs and cellulose fibers in both injection molding (IM) and fused deposition modeling (FDM). FTIR analysis revealed the removal of hemicellulose and lignin in alkalized WFs and uniform epoxy curing. Addition of fibers reduced PLA's thermal stability while acting as nucleating agents. Additionally, fibers augmented the storage modulus of biocomposites, with alkalized fibers exhibiting the highest tensile modulus in IM. FDM samples with a 0° raster angle showed superior impact resistance compared to IM counterparts. Moreover, raster angle significantly influenced FDM biocomposite properties, enhancing the tensile strength and modulus of untreated WF and cellulose fibers at 0°. Although FDM did not produce alkalized WF samples, epoxy impregnation emerged as a promising method for enhancing PLA/WF composite mechanical properties in the IM process, offering valuable insights for composite material development.