Transparent conductive oxides such as indium tin oxide (ITO) are standards for thin film electrodes, providing a synergy of high optical transparency and electrical conductivity. In an electrolytic environment, the determination of an inert electrochemical potential window is crucial to maintain a stable material performance during device operation. We introduce operando ellipsometry, combining cyclic voltammetry (CV) with spectroscopic ellipsometry, as a versatile tool to monitor the evolution of both complete optical (i.e., complex refractive index) and electrical properties under wet electrochemical operational conditions. In particular, we trace the degradation of ITO electrodes caused by electrochemical reduction in a pH-neutral, water-based electrolyte environment during electrochemical cycling. With the onset of hydrogen evolution at negative bias voltages, indium and tin are irreversibly reduced to the metallic state, causing an advancing darkening, i.e., a gradual loss of transparency, with every CV cycle, while the conductivity is mostly conserved over multiple CV cycles. Post-operando analysis reveals the reductive (loss of oxygen) formation of metallic nanodroplets on the surface. The reductive disruption of the ITO electrode happens at the solid-liquid interface and proceeds gradually from the surface to the bottom of the layer, which is evidenced by cross-sectional transmission electron microscopy imaging and complemented by energy-dispersive X-ray spectroscopy mapping. As long as a continuous part of the ITO layer remains at the bottom, the conductivity is largely retained, allowing repeated CV cycling. We consider operando ellipsometry a sensitive and nondestructive tool to monitor early stage material and property changes, either by tracing failure points, controlling intentional processes, or for sensing purposes, making it suitable for various research fields involving solid-liquid interfaces and electrochemical activity.
In situ transmission electron microscopy (TEM) is a powerful tool for advanced material characterization. It allows real-time observation of structural evolution at the atomic level while applying different stimuli such as heat. However, the validity of analysis strongly depends on the quality of the specimen, which has to be prepared by thinning the bulk material to electron transparency while maintaining the pristine properties. To address this challenge, a novel method of TEM samples preparation in plan-view geometry was elaborated based on the combination of the wedge polishing technique and an enhanced focused ion beam (FIB) workflow. It involves primary mechanical thinning of a broad sample area from the backside followed by FIB-assisted installation on the MEMS-based sample carrier. The complete step-by-step guide is provided, and the method’s concept is discussed in detail making it easy to follow and adapt for diverse equipment. The presented approach opens the world of in situ TEM heating experiments for a vast variety of fragile materials. The principle and significant advantage of the proposed method are demonstrated by new insights into the stability and thermal-induced strain relaxation of Ge Stranski–Krastanov islands on Si during in situ TEM heating. Graphical abstract
Anodic HfO2 memristors grown in phosphate, borate, or citrate electrolytes and formed on sputtered Hf with Pt top electrodes are characterized at fundamental and device levels. The incorporation of electrolyte species deep into anodic memristors concomitant with HfO2 crystalline structure conservation is demonstrated by elemental analysis and atomic scale imaging. Upon electroforming, retention and endurance tests are performed on memristors. The use of borate results in the weakest memristive performance while the citrate demonstrates clear superior memristive properties with multilevel switching capabilities and high read/write cycling in the range of 106. Low temperature heating applied to memristors shows a direct influence on their behavior mainly due to surface release of water. Citrate-based memristors show remarkable properties independent on device operation temperatures up to 100 °C. The switching dynamic of anodic HfO2 memristors is discussed by analyzing high resolution transmission electron microscope images. Full and partial conductive filaments are visualized, and apart from their modeling, a concurrency of filaments is additionally observed. This is responsible for the multilevel switching mechanism in HfO2 and is related to device failure mechanisms.
In this work, the impact of plasma treatment on Si wafers with native oxide on top was systematically investigated using spectroscopic ellipsometry. A general applicable three-layer optical model structure for ellipsometry data fitting was developed and employed on samples treated with the N2, O2, and N2/O2 mixture plasma. Oxide-growth, amorphization of crystalline Si, and the formation of a transition layer between the SiO2 and the amorphous Si were detected. The estimated thicknesses of produced layers were confirmed by complementary methods, which allow precise ultra-thin layers thicknesses detection, namely, angle-resolved x-ray photoelectron spectroscopy and transmission electron microscopy. The depth-resolved chemical composition and the direct thickness measurements of the produced amorphous structure revealed pronounced elemental gradients and the absence of sharp interfaces. Nitrogen gas used in the plasma process was found to be implanted mainly at the interface of the SiO2/transition layer in the form of Si3N4. However, it was verified that it is feasible to employ one general ellipsometry model consisting of SiO2/transition layer/amorphous Si on crystalline Si for all plasma species due to comparably low Si3N4 concentrations as well as its refractive index n and absorption k similarity to SiO2. Spectroscopic ellipsometry is nondestructive and can be efficiently applied to analyze whole wafers without any sample preparation. It can be concluded that the present approach to ellipsometry model development and verification is well suited for plasma-activated direct wafer bonding processes.
The results of studying the effect of the characteristic size on the rate of diffusion processes in nanometer Cu-Ni film systems have been reported. The film system has been prepared by sequential vacuum deposition of the components, and the activation energy of diffusion has been determined from a change in the electrical resistance of the film system in a heating-cooling cycle. It has been shown that the activation energy of grain-boundary diffusion decreases with decreasing characteristic size of the system and amounts to 0.25 eV for the film system with a characteristic size of 5 nm, which corresponds to an increase in the grain-boundary diffusion coefficient by 10 orders of magnitude with respect to massive samples.