In this work, a predictive model of attenuated guided wave propagation in carbon fiber–reinforced polymer using Rayleigh damping is developed. After a brief introduction, this article reviews the theory of guided waves in anisotropic composite materials. It follows with a discussion of the piezoelectric wafer active sensors, which are lightweight and inexpensive transducers for structural health monitoring applications. Experiments were performed on a carbon fiber–reinforced polymer panel to measure the dispersion curves and the piezoelectric wafer active sensors tuning curves. Lamb wave damping coefficient was modeled using the multi-physics finite element method and compared with experimental results. A discussion about the capability to simulate, with multi-physics finite element method commercial software, guided wave in composite material using the Rayleigh damping is developed. This article ends with conclusion, and suggestions for further work are also presented.
The present study explores a broad range of stoichiometry, with the [epoxy]/[acyl] ratio ranging from excess to unity for commercial diepoxide/sebacic acid vitrimer formulations, with 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD) used as the catalyst. In particular, it investigates to what extent side reactions promoted by off-stoichiometry mixtures can help achieve desirable thermomechanical properties (i.e. glass transition Tα, Young's modulus, strain at break, and strength) for an optimised vitrimer that behaves like a stiff material at room temperature, retaining its capacity to flow at high temperature while remaining insoluble. The possible role of TBD as an anionic initiator is tested in the homopolymerisation of epoxy and compared to a known anionic initiator, 2-phenylimidazole (2-PI). Attenuated total reflection infrared (ATR-IR) spectroscopy reveals different reaction speeds, but an identical scenario for either 2-PI or TBD. The acid + epoxy addition occurs first, then epoxy homopolymerisation takes place after di-carboxylic acid consumption; an ester typically forms in less than 20 min at 125 °C with TBD, while the formation of ether takes several hours. For all [epoxy]/[acyl] ratios ranging from 1 : 1 to 1 : 0.3, it is found that the integrity of the network is retained when subjected to 1,2,4 trichlorobenzene (TCB) solvent treatment. From the 1 : 1 to 1 : 0.75 epoxy to acyl ratio, the material retains full ability to flow and relax stresses under thermal stimulation, showing a 10 fold increase in viscosity and unchanged activation energy of about 100 kJ mol−1. Beyond 1 : 0.6 stoichiometry, a gradual transition from vitrimer to non-exchangeable crosslinked materials is observed as these networks show only partial stress relaxation due to interpenetration in the polyether network.
The most common researched area of damage in a composite material such as carbon fibre reinforced plastics (CFRP) used currently in aircraft construction is barely visible impact damage (BVID), significantly reducing mechanical properties. Early detection and qualification would improve safety and reduce the cost of repair. In this context, structural health monitoring (SHM) techniques have been developed that could monitor a structure at any time by using a network of sensors. Widely used discrete ceramic transducers can generate and sense Lamb waves travelling in the structure. Wave propagation must then be analysed for effective damage identification. An effective SHM system is desired to meet several demands, such as minimised weight penalty, non-intrusive system not interfering with the structure performance, cost-effectiveness for implementation with targeted sensitivity and area coverage, capability of monitoring non-accessible and critical hot spot regions, robustness and reliability. This review starts with an introduction on Lamb waves fundamentals and their use in SHM, and then particularly focuses on methods using piezoelectric transducers and mode selection. Some relevant applications on different structural configurations are discussed. Finally, recent developments on piezoelectric coating and direct-write sensor technology for tailored transducers are highlighted with some thoughts for near future research work.
The advancement of composite materials in aircraft structures has led to an increased need for effective structural health monitoring technologies that are able to detect and assess damage present in composite structures. The study presented in this article is interested in understanding self-sensing piezoelectric wafer sensors to conduct electromechanical impedance spectroscopy in glass fiber reinforced polymer composite to perform structural health monitoring. For this objective, multi-physics-based finite element method is used to model the electromechanical behavior of a free piezoelectric wafer active sensor and its interaction with the host structure on which it is bonded. The multi-physics-based modeling permits the input and output variables to be expressed directly in electric terms, while the two-way electromechanical conversion is done internally in the multi-physics-based finite element method formulation. The impedance responses are also studied in conditions when the sensor bonding layer is subject to degradation and when the sensor itself is subjected to breakage, respectively. To reach the goal of using the electromechanical impedance spectroscopy approach to detect damage, several damage models are generated on simplified orthotropic structure and laminated glass fiber reinforced polymer structures. The effects of the modeling are carefully studied through experimental validation. A good match has been observed for low and high frequencies.
Nanoparticle dispersion is widely recognised as a challenge in polymer nanocomposites fabrication. The dispersion quality can affect the physical and thermomechanical properties of the material system. Qualitative transmission electronic microscopy, often cumbersome, remains as the ‘gold standard’ for dispersion characterisation. However, quantifying dispersion at macroscopic level remains a difficult task. This paper presents a quantitative dispersion characterisation method using non-contact infrared thermography mapping that measures the thermal diffusivity (α) of the graphene nanocomposite and relates α to a dispersion index. The main advantage of the proposed method is its ability to evaluate dispersion over a large area at reduced effort and cost, in addition to measuring the thermal properties of the system. The actual resolution of this thermal mapping reaches 200 µm per pixel giving an accurate picture of graphene nanoplatelets (GNP) dispersion. The post-dispersion treatment shows an improvement in directional thermal conductivity of the composite of up to 400% increase at 5 wt% of GNP. The Maxwell-Garnet effective medium approximation is proposed to estimate thermal conductivity that compare favourably to measured data. The development of a broadly applicable dispersion quantification method will provide a better understanding of reinforcement mechanisms and effect on performance of large scale composite structures.