In this paper, the structure characteristics and magnetic properties of Fe₈₃Si₆B₆P_1.5C_1.5Cu₁Nb₁ amorphous alloy ribbons annealed at 550 °C for different times were systematically investigated using X-ray diffraction, vibrating sample magnetometer, and atom probe chromatography. The results show that high-density Cu atomic clusters of appropriate sizes help to stabilize the α-Fe(Si) phase and improve the uniformity of the grains to enhance the soft magnetic properties. The solubility difference between the α-Fe(Si) phase and the B-rich phase, the formation of a localized amorphous structure in the transition region, and the inhibition of nanograin growth. However, when the annealing time is extended, the size of the α-Fe(Si) grains decreases, the grain boundary density increases and secondary phases such as Cu clusters become pinning sites for magnetic domain walls. This leads to a decrease in soft magnetic properties, an increase in hard magnetic properties, and a rapid increase in coercivity. When annealed at 550 °C for 20 min, the number density of Cu atomic clusters was 9.18 × 10²² m⁻³, the spherical equivalent radius was 1.13 ± 0.29 nm, and the ribbons had good soft magnetic properties with a coercivity of 4.59 Oe. The saturation magnetic induction reached a peak value of 185.11 emu/g.

The present study investigates the microstructure and mechanical properties of ultra-low carbon bainitic steel (UCBS) under different cold rolling reductions. When the rolling reduction ratios were increased to 80%, the microstructure was refined, and the lath width of the bainite decreased from 601 nm to 252 nm. The ultimate tensile strength and yield strength increased from 812 MPa and 683 MPa to 1195 MPa and 1150 MPa, respectively, whereas the elongation decreased from 15.9% to 7.9%. In addition, the dislocation density increased from 8.3 × 10¹³ m⁻² to 4.87 × 10¹⁴ m⁻² and a stronger γ-fiber texture was obtained at the 80% cold rolling reduction ratio. The local stress distribution and kernel average misorientation were not uniform and became more severe with increased rolling reduction ratios. The strength increment of UCBS was primarily due to boundary strengthening and dislocation strengthening. The theoretical strength increment agreed well with the experimental measurements, which can be helpful for the design and production of UCBS for broad engineering applications.

In this paper, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray stress meter (XRSA), atom probe tomography (APT), hardness, and tensile tests were used to study the effect of tempering temperature on the microstructure and properties of Fe-9Ni-2Cu steel. The results show that after the quenched samples were tempered at 460 °C for 2 h, the hardness values increased from 373 to 397 HV, and elongation also increased from 13% to 16%. With the tempering temperature increasing from 460 to 660 °C, the hardness firstly decreases from 397 to 353 HV and then increases to 377 HV, while the elongation increases to 17% and then decreases to 11%. The variation of the mechanical properties greatly depends on the evolution of the Cu-rich phase and carbides. The precipitation strengthening of the Cu-rich phase and carbides leads to the increase of hardness, but when the precipitate is coarsened, the precipitation strengthening weakens, and then, the hardness increases. When the tempering temperature is 560 °C, a large amount of stable reverse transformation austenite was formed with a content of 7.1%, while the tensile strength reached the lowest value of 1022 MPa and the elongation reached the maximum value of 17%.

The current work synthesized Ni-SiC composite coating with different SiC microparticle contents. The role of the SiC microparticle in designing the Ni-SiC composite microstructure was revealed. The SiC microparticle physically interrupted the continuous growth of the underlying columnar Ni grains. The columnar Ni grain between the embedded SiC microparticle grew without disturbance. Only upon SiC microparticles was a new layer starting with refined Ni grains observable. The vertical columnar Ni grains reappeared as the position departed the SiC microparticle upper surface. The increase in the contents of the SiC microparticle led to an increased level of grain refinement and the elimination of the (200) fiber texture. Besides that, the number of V-shaped valleys increased as well. Corrosion testing results show that the corrosion resistance of Ni-SiC composite coating increased with the increased SiC contents, which was mainly due to the optimized microstructure.

This paper presents obtaining a single-phase ferrite layer with low content of carbon (the average thickness is about 156–246 µm) on the surface of 0.45% carbon steel by precisely designing the cooling rate during heat treatment, and its mechanical properties show a graded change in the cross-section. It may be achieved by preparing gradient/multilayer materials with more commonly utilized structures or a specific performance. Combining with phase identification by employing electron backscatter diffraction (EBSD) of the layer in this study is BCC ferritic phases. Based on the examination of Continuous Cooling Transformation (CCT) curves, the following conclusions are given. Under the cooling process with gradient temperature, a ferrite layer first forms on the outer lower temperature surface of the 0.45% carbon steel and subsequently develops by pushing the surplus carbon to the inner higher temperature austenite region. It is corroborated by the experimental findings of carbon contents dispersion acquired by electron probe microanalyzer (EPMA). Finally, the experimental findings of grain orientations and size distribution defined by electron backscatter diffraction (EBSD) are given as requirements for microscopic interpretation of the combination of excellent strength and bending capabilities of materials. Furthermore, the experimental findings of oxidation precisely specified the cooling rate during heat treatment of Cu coating samples, which are defined as criteria for identifying the production mechanism of the surface ferrite layer. It provides a theoretical explanation and direct experimental proof for creating the ferrite layer on the surface.

Ni–Al–Ti nanocomposite coatings were synthesized by electrodeposition. The tailoring role of Al and Ti particles in the co-deposition behaviors of nanocomposite coatings was comprehensively investigated by analyzing the time-dependent current density and electric field near the co-deposited particles. The results showed that the Al and Ti particles caused different co-deposition behaviors of Ni deposits, consequently bringing in the gradual increase in the surface dendritic structure, the refinement of grain sizes, and the decrease in the [200] fiber texture of the nanocomposite coatings with the decrease in the Al/Ti weight ratio. COMSOL simulations verified the different co-deposition mechanisms of Ni grains near the two kinds of particles, which was vitally determined by the different conditions of current density and electric field near the particles. The micro-hardness results revealed that the decreased Al/Ti weight ratio led to enhanced micro-hardness of the nanocomposite coating; in addition, the maximum hardness of the nanocomposite coating was 604.3 HV0.2 for an Al/Ti weight ratio of 1:4. Thus, the time-dependent current density and electric field near co-deposited Al and Ti particles determined the microstructure and property of the Ni–Al–Ti nanocomposite coatings.