Martin Kraus

Mr. Martin Kraus

Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU)
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Wear
Verified
Journal Article
Open access
Martin KrausMartin Kraus
Martin Kraus
MLMatthias Lenzen
Matthias Lenzen
Marion MerkleinMarion Merklein
Marion Merklein

15 April 2003 in Journal of Applied Physics
Verified
Journal Article
Open access
JLJorge Luque
Jorge Luque
Martin KrausMartin Kraus
Martin Kraus
AWAlexander Wokaun
Alexander Wokaun
KHKen Haffner
Ken Haffner
UKUlrich Kogelschatz
Ulrich Kogelschatz
BEBaldur Eliasson
Baldur Eliasson
The gas temperatures were determined by optical emission in a dielectric-barrier discharge at atmospheric pressure. The feed gases were either pure CH4 to yield higher hydrocarbons or CH4/CO2 mixtures to yield synthesis gas (H2/CO). The monitored emission was from the CH radical A 2Δ–X 2Π electronic system and the gas temperature range characterized was from 300 to 600 K. The technique described in this article enables the measurement of the neutral gas temperature in the discharge that is not accessible via conventional methodology using thermocouples. A bimodal rotational population distribution in the CH A 2Δ v′=0 state was determined in the investigated gas mixtures of CO2/CH4 and in pure methane. Most of the rotational population was at temperatures from 300 to 600 K depending on experimental conditions, which are only slightly higher than the set temperature of the reactor. A small fraction of the emitting species was found to have a much higher rotational temperature of ∼4000 K for the pure methane gas and the mixture of CO2 and CH4. The low temperature rotational distribution correlated with changes in the ambient conditions and is used as a thermometer, while the high rotational temperature component and the vibrational temperature reflect the excess of energy during the CH radical formation by electron impact dissociative excitation of methane, and the extent of collisional relaxation before emission takes place.

1 September 2020 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
Martin KrausMartin Kraus
Martin Kraus
MMMarion Merklein
Marion Merklein

Verified
Journal Article
Open access
PDF file
David RömischDavid Römisch
David Römisch
Martin KrausMartin Kraus
Martin Kraus
Marion MerkleinMarion Merklein
Marion Merklein
Due to stricter emission targets in the mobility sector and the resulting trend towards lightweight construction in order to reduce weight and consequently emissions, multi-material systems that allow a material to be placed in the right quantity and in the right place are becoming increasingly important. One major challenge that is holding back the rapid and widespread use of multi-material systems is the lack of adequate joining processes that are suitable for joining dissimilar materials. Joining processes without auxiliary elements have the advantage of a reduced assembly effort and no additional added weight. Conventional joining processes without auxiliary elements, such as welding, clinching, or the use of adhesives, reach their limits due to different mechanical properties and chemical incompatibilities. A process with potential in the field of joining dissimilar materials is joining without an auxiliary element using pin structures. However, current pin manufacturing processes are mostly time-consuming or can only be integrated barely into existing industrial manufacturing processes due to their specific properties. For this reason, the present work investigates the production of single- and multi-pin structures from high-strength dual-phase steel HCT590X + Z (DP600, t0 = 1.5 mm) by cold extrusion directly out of the sheet metal. These structures are subsequently joined with an aluminium sheet (EN AW-6014-T4, t0 = 1.5 mm) by direct pin pressing. For a quantitative evaluation of the joint quality, tensile shear tests are carried out and the influence of different pin heights, pin number, and pin arrangements, as well as different joining strategies on the joint strength is experimentally evaluated. It is proven that a single pin structure with a diameter of 1.5 mm and an average height of 1.86 mm achieves a maximum tensile shear force of 1025 N. The results reveal that the formation of a form-fit during direct pin pressing is essential for the joint strength. By increasing the number of pins, a linear increase in force could be demonstrated, which is independent of the arrangement of the pin structures.

6 March 2014
Verified
Conference Paper
Closed access
PDF file
AFAnne Feuer
Anne Feuer
CKClemens Kunz
Clemens Kunz
Martin KrausMartin Kraus
Martin Kraus
VOVolkher Onuseit
Volkher Onuseit
RWRoy E Weber
Roy E Weber
FHFrank Hermanutz
Frank Hermanutz
To enable the direct-spinning process of super-micro fibres (< 0.5 dtex) suitable for novel medical, hygienical and technical products microhole arrays with diameters down to 25 μm in very high quality are required. Using ultrashort pulses together with a helical drilling optics microholes with high accuracy were manufactured in metals of a thickness in the range of 0.3 mm. However, the required process time for a single microhole ranges up to several ten seconds. Simple energy balance considerations show that higher averaged powers - either achieved with larger pulse energies or an increased repetition rate - considerable reduce the process time. In this case plasma formation and heat accumulation show an increased formation of melt and recast. Thus, the objective is to increase the productivity while maintaining consistent quality of the microholes. With this aim, the influence of pulse energy and repetition rate on the borehole geometry, processing quality and process efficiency was investigated for helical drilling. In the present research work a TruMicro 5250 laser source (tp = 8 ps, λ=515 nm, fR=800 kHz) was used. To determine the process time of the microhole the transmitted laser radiation was recorded. A systematic evaluation of the process quality and process time dependent on pulse energy and repetition rate will be presented in this contribution. First laser manufactured spinning nozzles with microhole diameters down to 25 μm processed in 0.24 mm thick AuPt alloy were used to fabricate unique super-micro fibres with yarn counts down to 0.2 dtex.

7 April 2022 in CIRP Annals
Verified
Journal Article
Open access
PHPeter Hetz
Peter Hetz
Martin KrausMartin Kraus
Martin Kraus
Marion MerkleinMarion Merklein
Marion Merklein