This letter presents a novel reconfigurable, high-efficiency class-F power amplifier (PA) structure, using a commercial GaN-HEMT, that achieves dual-band configuration not only at the fundamental frequency but also at the harmonics. With a proper harmonic tuning structure, the need for an extra filtering section is eliminated, resulting in a high dual-band efficiency with a reduced number of components and size. The reconfigurable structure uses commercial single-pole-double-throw (SPDT) and single-pole-single-throw (SPST) MEMS switches optimally placed on the stubs to select between 900 and 1800 MHz. The reconfigurable PA achieves a measured power-added efficiency (PAE) of 69.5% and a power gain of 13.6 dB while delivering an output power of 39.1 dBm at 900 MHz. At 1800 MHz, the amplifier achieves a PAE of 57.9%, a power gain of 10.5 dB, and an output power of 38.5 dBm.

A novel reconfigurable CMOS class-F power amplifier (PA) at 2.4 GHz is proposed in this paper. It is able to match the output load variations mainly due to the effect of hand and head on a mobile phone. The effect of load variation on power-added efficiency (PAE), output power, and distortion is compensated by reconfiguring the output network using an impedance tuner. The tuner controls the output matching at fundamental frequency without affecting the class-F harmonic tuning up to 3 ^rd harmonic. To the best of our knowledge, this is the first design of a CMOS class-F PA addressed to compensate the effect of load variation. Measurement results for 50 Ω load impedance show a maximum PAE of 26% and maximum output power of 19.2 dBm. The measured total harmonic distortion is 4.9%. Measurement results for load values other than 50 Ω show that PAE increases from 6.5% (not-tuned PA) up to 19.9% (tuned PA) with the same output power (19.2 dBm). Tuning also reduces the adjacent-channel leakage ratio by 5 dB and the spectral regrowth of a Wi-Fi signal at the PA output. The size of the fabricated chip is 1.6 mm × 1.6 mm.

A 16 switched beam lens based antenna with a coverage area of $\pm 30 ^\circ$ in the horizontal plane and from 0 to $-20 ^\circ$ in the vertical plane has been built and tested. The intended use of the antenna is as part of a smart repeater servicing the coverage area of a 5G wireless communication system operating in the n258 band of the 5G Frequency Range 2, from 24.25 to 27.5 GHz. The antenna has been built using state-of-the-art materials and components in order to assess the performance of this antenna concept. The overall antenna losses including the feeding network are of the order of 8 dB and the realized gain in the $80 \%$ of the coverage area is above 11 dB.

Nonlinear effects in the radio front-end can degrade communication quality and system performance. In this paper we present a new design technique for reconfigurable antennas that minimizes the nonlinear distortion and maximizes power efficiency through the minimization of the coupling between the internal switching ports and the external feeding ports. As a nonlinear design and validation instance, we present the nonlinear characterization up to 50 GHz of a PIN diode commonly used as a switch for reconfigurable devices in the microwave band. Nonlinear models are extracted through X-parameter measurements supported by accurate calibration and de-embedding procedures. Nonlinear switch models are validated by S-parameter measurements in the low power signal regime and by harmonic measurements in the large-signal regime and are further used to predict the measured nonlinearities of a reconfigurable antenna. These models have the desired particularity of being integrated straightforwardly in the internal multi-port method formulation, which is used and extended to account for the power induced on the switching elements. A new figure of merit for the design of reconfigurable antennas is introduced—the power margin, that is, the power difference between the fed port and the switching elements, which combined with the nonlinear load models directly translates into nonlinearities and power-efficiency-related metrics. Therefore, beyond traditional antenna aspects such as port match, gain, and beam orientation, switch power criteria are included in the design methodology. Guidelines for the design of reconfigurable antennas and parasitic layers of minimum nonlinearity are provided as well as the inherent trade-offs. A particular antenna design suitable for 5G communications in the 3.5 GHz band is presented according to these guidelines, in which the specific switching states for a set of target performance metrics are obtained via a balancing of the available figures of merit with multi-objective separation criteria, which enables good control of the various design trade-offs. Average Error Vector Magnitude (EVM) and power efficiency improvement of 12 and 6 dB, respectively, are obtained with the application of this design approach. In summary, this paper introduces a new framework for the nonlinear modeling and design of reconfigurable antennas and provides a set of general-purpose tools applicable in cases beyond those used as examples and validation in this work. Additionally, the use of these models and guidelines is presented, demonstrating one of the most appealing advantages of the reconfigurable parasitic layer approach, their low nonlinearity.