In this study, a three-dimensional compact antenna solution for the automotive industry is proposed. The antenna solution is designed to fit in a shark-fin case and is easily fabricated from a printed circuit board and a metal sheet with low-cost process and materials. The antenna solution covers Long Term Evolution (LTE), GPS, WLAN, and Wireless Access in the Vehicular Environment (WAVE) bands (850 MHz, 1575 MHz, 2.4 GHz, and 5.9 GHz, respectively). The planar inverted-F antennas are used as multiple-input-multiple-output antennas for the LTE band due to their low-profile structure. Modified planar monopoles are used to obtain omnidirectional radiation patterns for WLAN and WAVE bands. Antenna characteristics such as return loss, isolation, and radiation pattern have been simulated and measured to confirm the possibility for use in automotive applications.
We investigate time-dependent inorganic ligand exchanging effect and photovoltaic performance of lead sulfide (PbS) nanocrystal films. With optimal processing time, volume shrinkage induced by residual oleic acid of the PbS colloidal quantum dot (CQD) was minimized and a crack-free film was obtained with improved flatness. Furthermore, sufficient surface passivation significantly increased the packing density by replacing from long oleic acid to a short iodide molecule. It thus facilities exciton dissociation via enhanced charge carrier transport in PbS CQD films, resulting in the improved power conversion efficiency from 3.39% to 6.62%. We also found that excess iodine ions on the PbS surface rather hinder high photovoltaic performance of the CQD solar cell.
3 November 2022 in IEEE Microwave and Wireless Technology Letters
A D-band $\times$ 8 frequency multiplier is presented in this letter. The $\times$ 8 frequency multiplier consists of two stages of the newly proposed common load complementary push-push doublers (CL-CPPDs) and one stage of NMOS push-push doubler. The proposed CL-CPPD uses a single load to generate a balanced output with high harmonic rejection (HR) and can be easily cascaded using transformers for a high multiplication ratio with low dc power consumption. The chip is fabricated by using a 40-nm CMOS technology, and it achieves a maximum output power of $-$ 2.48 dBm with an input power of $0$ dBm in the frequency range of 131.2–144.8 GHz. All HRs are over 34 dBc in the frequency range of 131.2–144.8 GHz. The total dc power dissipation is 41.4 mW when supplied from a single voltage of 0.9 V and occupies 0.37 ${\mathrm{mm}}^{2}$ of the chip area.
This paper presents 77-GHz CMOS radar transmitter and receiver chips equipped with monopole feeders for use in frequency-modulated continuous-wave radar systems. The on-chip monopole feeder can feed not only the aperture of waveguides but also the slots on planar circuits by simply attaching the chips to a printed circuit board using a low-cost non-conductive epoxy. With the aid of a high ratio multiplier and the proposed on-chip feeder, a radar system can easily be integrated without needing to use precise and expensive millimeter-wave packaging technologies. In order to experimentally confirm this, the chips integrated with waveguides are first measured and a full radar system integrated on the planar circuit is evaluated using the microstrip patch antennas. Finally, with the benefit of compact integration technology, the design of a five-channel 3-D environmental sensing radar for small-unmanned aerial vehicles is presented.
This work, for the first time to our best knowledge, presents a W-band multi-channel frequency-modulated continuous-wave (FMCW) radar system on low-cost FR-4 substrates. A center-fed patch array antenna on an FR-4 substrate can achieve a maximum gain of 10.8 dBi. It is enabled by aperture coupled feeding using an on-chip feeder implemented on a CMOS radar transmitter (Tx) and receiver (Rx). The proposed radar system consists of one Tx and four Rx channels placed in the back cavity of a microstrip array antenna like an active array antenna system. Additionally, Tx and Rx chipsets include a wideband frequency multiplier with high multiplication ratio of 63, making it easy to distribute reference FMCW waveform synthesized at a very low frequency about 1.25 GHz for 79 GHz output using direct digital synthesis (DDS). Extending the number of channels and implementing various waveforms can be easily accomplished with very good phase noise. The functionality of the proposed radar system on low-cost substrates is confirmed by distance and angle measurements.
30 December 2012 in JOURNAL OF SEMICONDUCTOR TECHNOLOGY AND SCIENCE
A fully-integrated low power K-band radar transceiver in 130 ㎚ CMOS process is presented. It consists of a low-noise amplifier (LNA), a downconversion mixer, a power amplifier (PA), and a frequency synthesizer with injection locked buffer for driving mixer and PA. The receiver front-end provides a conversion gain of 19 ㏈. The LNA achieves a power gain of 15 ㏈ and noise figure of 5.4 ㏈, and the PA has an output power of 9 ㏈m. The phase noise of VCO is -90 ㏈c/㎐ at 1-㎒ offset. The total dc power dissipation of the transceiver is 142 ㎽ and the size of the chip is only 1.2 × 1.4 ㎟.