Bees Algorithm (BA) is a popular meta-heuristic method that has been used in many different optimization areas for years. In this study, a new version of combinatorial BA is proposed and explained in detail to solve Traveling Salesman Problems (TSPs). The nearest neighbor method was used in the population generation section of BA, and the Multi-Insert function was added to the local search section instead of the Swap function. To see the efficiency of the proposed method, 24 different TSPs were used in experimentation and the obtained results were compared with both classical combinatorial BA and other successful meta-heuristic methods. After detailed analyses and experimental studies on different problems, it has been observed that the proposed method performs well for TSPs and competes well with other methods.
In this study, the design of the torsion and compression springs of the foldable wing mechanism used in the missile is considered an optimization problem. After the missile leaves the tube, the wings waiting in a closed state must be opened and fixed within a specific time. The study it is aimed to maximize the energy stored by the springs so that the wing can be opened in a minimum time. In this context, the energy equation in both publications is defined as the objective function in the optimization process. Wire diameter, coiling diameter, coiling number, and deflection parameters required for spring design were determined as optimization variables. There are geometrical constraints for the variables due to the dimensions of the mechanism and there are also safety factor constraints due to the loads to which the springs are exposed. The Bees Algorithm (BA) was used to solve this optimization problem and perform the spring design. The energy values obtained with BA were better than the values obtained with the Design of Experiment (DOE) study before. The springs and mechanism designed with the parameters obtained from the optimization were first analyzed in the ADAMS program. Afterward, experimental tests carried out by integrating the produced springs into the actual mechanism. As a result of the tests, it was observed that the wing opened at approximately 90 ms. This value is well below the project target of 200 ms. In addition, there is only a 16 ms difference between the analysis and the experimental results.
Gimbal is a system that provides locking and tracking of the seeker on the target in missiles and increases the angle of view with its mobility in two axes. In this study, stabilization of a two-axis gimbal system used in the missile was carried out. In gimbal stabilization, adaptive controllers are preferred instead of classical controllers due to unbalance, cross-coupling, and unmeasurable disturbances. A Self Tuning PID controller based on Fuzzy Logic was developed for axis controls in the stabilization algorithm. Thanks to this controller, which works with the principle of choosing the most appropriate coefficient at every step, it was possible to control with less than 3% errors in the tests performed with the flight simulator. In addition, a PID controller whose coefficients are optimized with Particle Swarm Optimization is designed for comparison purposes. In experimental studies, it was seen that PID with adjustable coefficients gave better results than the fixed PID.
In this study, the LabVIEW modeling of a permanent magnet synchronous generator that will be used in wind turbine and the voltage control with artificial neural networks on the model are done. Typically synchronous, asynchronous and direct current generators are used in wind turbines. In the scope of this study, synchronous generators are preferred due to the advantages such as high efficiency and high reliability. the artificial neural networks are used in the control of excitation circuit in taking into account the dynamic nature of the wind.
The model predictive control (MPC) tries to find the best control output by optimizing among the predictions. In this context, determining the objective function of optimization is a critical process. This study discusses the velocity control of the mini brushed direct current (BDC) motor used in the actuator with MPC. Four different functions have been defined to design the most appropriate cost function for MPC by considering the parameters that may be effective in the motor dynamics such as velocity, current, power, and switching states. Software in the Loop (SIL), one of the modeling-based testing methods, was used within the scope of testing the algorithms. After the SIL tests, it has been observed that the mini BDC motor can be successfully controlled with simple adjustments to the cost function of the MPC. As a result of the analysis obtained the best results with the objective function consisting of velocity error, estimated current, and the difference between the two estimated velocity values. With this controller, the BDC motor can be controlled without overshoot and with a steady-state error of less than 2% under load.
In this study, the model predictive control (MPC) method was used within the scope of the control of the permanent magnet synchronous motor (PMSM). The strongest aspect of the MPC, the ability to control multiple components with a single function, is also one of the most difficult parts of its design. The fact that each component of the function has different effects requires assigning different weight coefficients to these components. In this study, the Bees Algorithm (BA) is used to determine the weights. Using the multi-objective function in BA, it has been tried to determine the weights that reduce the current values together with the speed error. Three different PI controllers have been designed to compare the MPC method. The coefficients of one of these are tuned with BA. Good Gain Method and Tyreus-Luyben Method were used in the other two. As a result of experimental studies, it has been observed that MPC can control PMSM more smoothly and accurately than PI controllers, with weights optimized with BA. With MPC, PMSM has been controlled with 15% settling time than other controllers and also with no overshoot.