liu chunyang

Dr. liu chunyang


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 January 2016 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
LCliu chunyang
liu chunyang
FHFuxiang Huang
Fuxiang Huang
XWXinhua Wang
Xinhua Wang

17 December 2015 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
LCliu chunyang
liu chunyang
FHFuxiang Huang
Fuxiang Huang
JSJinliang Suo
Jinliang Suo
XWXinhua Wang
Xinhua Wang

6 November 2017 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
LCliu chunyang
liu chunyang
MYMotoki Yagi
Motoki Yagi
XGXu Gao
Xu Gao
SKSun-Joong Kim
Sun-Joong Kim
FHFuxiang Huang
Fuxiang Huang
SKShin-Ya Kitamura
Shin-Ya Kitamura

6 May 2021 in Metals
Verified
Journal Article
Open access
PDF file
LCliu chunyang
liu chunyang
YJYi Jia
Yi Jia
LHLixia Hao
Lixia Hao
SHShaowei Han
Shaowei Han
FHFuxiang Huang
Fuxiang Huang
SKShin-Ya Kitamura
Shin-Ya Kitamura
The inclusion of the MgO·Al2O3 (MA) spinel and CaO–Al2O3 are occasionally observed during the refining of Al–killed steel, even without the intentional additions of Ca and Mg. Many studies have focused on the source of Mg and Ca; however, especially for the formation of CaO–Al2O3–type inclusions, some recent results showed that Ca was difficult to dissolve from refining slag, even when the Al content in molten steel was high. To confirm these differences, industrial experiments were designed in this study, and the effects of the FeO and MnO contents, as well as the impurities of the alloying materials, were discussed. The results showed that, when the FeO and MnO contents in slag were high (about 10 mass%) at the start of LF (ladle furnace), all inclusions remained as Al2O3, despite alloying. Using the slag with low FeO + MnO content (<1~2 mass%), the Al2O3 inclusions changed to the MA spinel, but CaO–Al2O3 inclusions were not observed, indicating that CaO–Al2O3 inclusions were difficult to form by the steel/slag reactions under the current conditions. Only for the molten steel that contained a low level of dissolved oxygen and a large amount of Fe–Si, which contained Ca as the impurity was added, CaO–Al2O3 inclusions were generated.

14 September 2015 in Metallurgical Research & Technology
Verified
Journal Article
Closed access
PDF file
LCliu chunyang
liu chunyang
FHFuxiang Huang
Fuxiang Huang
XWXinhua Wang
Xinhua Wang
GYGuangwei Yang
Guangwei Yang
In practice, hot metal with low sulfur content is inevitably resulfurized in an oxygen converter. In order to fully understand the steel resulfurization process and control the sulfur content at the end of the converter blowing, resulfurization behavior of steel by slag (CaO-FeO-SiO2-CaS) was investigated in this study. The rate-controlling step was obtained and further confirmed through Si-Mo electric resistance furnace and induction furnace experiments. The effects of slag parameters including slag basicity, slag amount, initial sulfur content, CaF2 and MgO content on the rate and extent of resulfurization were investigated through induction furnace experiments. The results indicate that the rate-controlling step of resulfurization lies in sulfur transfer in the slag phase. The initial sulfur content and slag amount have a positive effect on both the rate and extent of resulfurization, while slag basicity has a negative effect on either the rate or extent of resulfurization. CaF2 addition promotes the rate of resulfurization but has little impact on the resulfurization extent. MgO addition has complex effects on resulfurization. In addition, a kinetic model was developed and its calculation results agreed well with the experimental data.