Matters concerned with organizing combustion of different types of coal-water slurries in coalfired boilers at thermal power stations are considered. Recommendations for improving the economic and environmental indicators and for achieving more reliable operation of furnace devices and boiler as a whole are given.
The article presents an overview of modern analytical methods and experimental studies on the use of heat exchangers as part of different schemes, as well as technologies that increase the efficiency of heat exchangers using renewable energy sources. The main types of heat exchangers, and the principles of their operation, are considered. In addition, modern technologies for increasing the efficiency of heat exchangers through design are described. The practical experience of using plate heat exchangers in industry has been studied. An overview of the software development that is used in the design and optimization of heat exchange devices, as well as for the improvement of their energy efficiency, is presented. The presented mathematical models can be used for software that is applicable both to individual segments of plates of heat exchangers and heat exchangers in general, taking into account the dependence of the installation of the entire circuit on environmental parameters and location. In conclusion, recommendations are given for further research directions in the field of using heat exchangers with the inclusion of renewable energy sources. The technique of an energy technology complex, including a heat pump, a photovoltaic panel, and a desalination plant, is presented. The methodology is built around the basic design and energy balance of the complex, and it is also considered from the point of view of the exergetic balance. This allows for the use of additional components, such as a turbo expander for the implementation of the organic Rankine cycle, a wind turbine, and a solar concentrator. This scientific approach can become unified for the design and operation of an energy technology complex. In addition, an exergetic calculation method is presented for a thermal desalination plant operating as part of an energy technology complex with renewable energy sources.
The problem of increasing the reliability of wind turbines exists in the development of new offshore oil and natural gas fields. Reducing emergency situations is necessary due to the autonomous operation of drilling rigs and bulk seaports in the subarctic and Arctic climate. The relevance of the topic is linked with the development of a methodology for theoretical and practical studies of gas dynamics when gas flows in a pipe, based on a mathematical model using new mathematical methods for calculation of excess speeds in case of wind gusts. Problems in the operation of offshore wind turbines arise with storm gusts of wind, which is comparable to the wave movement of the gas flow. Thus, the scientific problem of increasing the reliability of wind turbines in conditions of strong wind gusts is solved. The authors indicate a gross error in the calculations when approximating through the use of the Fourier series. The obtained results will allow us to solve one of the essential problems of modeling at this stage of its development, namely: to reduce the calculation time and the adequacy of the model built for similar installations and devices. Experimental studies of gas-dynamic flows are carried out on the example of a physical model of a wind turbine. In addition, a computer simulation of the gas-dynamic flow process was carried out. The use of new approximation schemes in processing the results of experiments and computer simulation can reduce the calculation error by 1.2 percent.
This review analyzes articles on the mathematical modeling of economic facts and processes. Mathematical modeling of the economy has rapidly developed in the past and current centuries. This is explained by the fact that, firstly, economics does not tolerate full-scale experiments, secondly, mathematical modeling significantly improves the accuracy of research results, and, finally, thirdly, economics becomes a science only when it is based on mathematics. The article presents an overview of the main methods of economic modeling used in scientific research over the past twenty years. The review does not claim to cover all areas, methods, and models used in scientific research in the field of economics. This cannot be done in one article. Mathematical modeling of only three sections of economic theory is considered: macroeconomics, microeconomics, and state regulation of the economy. The review of research methods and models in the microeconomics section, which are available in the scientific research toolkit but have already been described in the macroeconomics section, has been omitted. Only effective, practice-tested models are used in the Review. We hope that this review will be useful to scientists involved in the indirect study of economic phenomena and processes.
Approximation of piecewise linear and generalized functions is an important and difficult problem. These functions are widely used in mathematical modeling of various processes and systems, such as: automatic control theory, electrical engineering, radio engineering, information theory and transmission of signals and images, equations of mathematical physics, oscillation theory, differential equations and many others. The widespread use of such functions is explained by their positive properties. For example, piecewise linear functions are characterized by a simple structure over segments. However, these features also have disadvantages. For example, in the case of using piecewise linear functions, solutions have to be built in segments. In this case, the problem of matching the obtained solutions at the boundaries of the segments arises, which leads to the complication of the research results. The use of generic functions has similar disadvantages. To eliminate shortcomings in practice, one resorts to the approximation of these functions. There are a large number of well-known methods for approximating piecewise linear and generalized functions. Recently, new methods for their approximation have been developed. In this study, an attempt was made to generalize and discuss the existing methods for approximating the considered functions. Particular emphasis is placed on the description of new approximation methods and their applications in various fields of science and technology. The publication-based review discusses the strengths and weaknesses of each method, compares them, and considers suitable application examples. The review will undoubtedly be interesting not only for mathematicians, but also for specialists and scientists working in various applied fields of research.
This study focuses on the development of new methodological approaches to dust-preparation and burning of separated particles, including through the use of polyfractional ensembles. Coal dust screening by means of sieve analysis is described in standard methods. However, in order to further use the results obtained during mathematical modeling of particle motion in fuel-air mixture and exothermal reactions of oxidation while burning in a torch, it must be possible to differentiate and integrate continuous functions. The methodology is based on the continuity of particle motion in a mixture with air in the calculation of aerodynamic and heat-mass exchange processes in a torch. The paper employs new scientific approaches to transforming and normalizing a continuously differentiable function described by the Gauss curve. We propose to combine mathematical modeling of such functions with methods of approximation of piece-linear functions developed by Professor S. V. Aliukov. The implementation of such methods helps reduce calculation errors of particle size and deviations thereof from average equivalent diameter and to avoid the Gibbs effect while differentiating. The paper contains analytical calculations based on the proposed method and experimental data. Quantitative and qualitative results of comparing analytical and experimental data are also presented. We provide recommendations on the further use and extension of the range of the results obtained in a computer simulation of fuel production and burning processes in a torch.