The authors analyzed the state of the process scheme, which is a structural part of the water supply treatment facilities. The research results can be applied in oil and gas, chemical, metallurgical and energy industries. In particular, the authors for the first time propose an efficient scheme for the reuse of heat to obtain purified water. Currently, a way to reduce energy consumption by introducing a plant based on an organic Rankine cycle has been considered. The metallurgical production has such equipment as converters, coke ovens, scrubbers, gas ducts, cooling boilers, waste heat boilers. The heat recovery schemes developed by the authors increase the efficiency of the process equipment in the metallurgical industry. In the work of enterprises, low-potential heat of soil, water, air is increasingly used. One of the main directions of energy saving to increase the energy efficiency of the boiler house is to increase the heat utilization rate of the fuel at power plants. Boiler houses that run on gas lose at least 13-18% of heat with flue gases. In the article, the authors propose to combine the methods of heat utilization. Namely, a contact heat exchanger and an organic Rankine cycle are used. The water temperature is significantly reduced due to the fact that the collectors are designed to transport water. In this regard, experts consider it expedient to utilize the heat of wastewater not only at treatment plants, but also directly in the building itself. Prospects for the use of the authors’ developments are associated with their further implementation at industrial enterprises of the metallurgical industry.
13 August 2007 in IEEE Transactions on Plasma Science
A method of cleaning vacuum arc plasma from the droplet fraction of cathode erosion by creating conditions favorable for ignition and further operation of "droplet spots" in plasma is proposed. Such conditions are realized in the reflective arc discharge. Plasma of this discharge has substantially higher temperature and density in comparison with plasma of usual vacuum arc at the same current. The experiments performed have shown that, in contrast with the usual vacuum arc, arc at the reflective discharge mode results in several times decrease in the number of droplets residuary after passage through plasma. The experimental results are being discussed in the term of heat exchange between droplets and surrounding plasma. The method proposed opens up new possibilities of cleaning vacuum arc plasma from droplets.
20 October 2017 in IOP Conference Series: Earth and Environmental Science
In article, the direct torque control method of the synchronous electric drive is considered. This control method is characterized by high performance, robustness and small frequency of switching of keys of the converter. The algorithms and structure of direct torque control of the synchronous electric drive allow creating its operation modes by impact on the form of a triangle with sides: flux linkage of the stator, a rotor, and resultant flux linkage.
The problem of increasing the reliability of wind turbines exists in the development of new offshore oil and natural gas fields. Reducing emergency situations is necessary due to the autonomous operation of drilling rigs and bulk seaports in the subarctic and Arctic climate. The relevance of the topic is linked with the development of a methodology for theoretical and practical studies of gas dynamics when gas flows in a pipe, based on a mathematical model using new mathematical methods for calculation of excess speeds in case of wind gusts. Problems in the operation of offshore wind turbines arise with storm gusts of wind, which is comparable to the wave movement of the gas flow. Thus, the scientific problem of increasing the reliability of wind turbines in conditions of strong wind gusts is solved. The authors indicate a gross error in the calculations when approximating through the use of the Fourier series. The obtained results will allow us to solve one of the essential problems of modeling at this stage of its development, namely: to reduce the calculation time and the adequacy of the model built for similar installations and devices. Experimental studies of gas-dynamic flows are carried out on the example of a physical model of a wind turbine. In addition, a computer simulation of the gas-dynamic flow process was carried out. The use of new approximation schemes in processing the results of experiments and computer simulation can reduce the calculation error by 1.2 percent.
A theoretical model is developed for the process of energy exchange between a spherical drop and a nonequilibrium plasma. It is demonstrated that, in a certain range of the plasma parameters, a quasistationary temperature of the drop can be maintained in two different heat exchange regimes. In one of these, the energy flux from plasma to drop is compensated by cooling due to the thermal emission of electrons; in the other, the energy supply is equilibrated by intensive evaporation of the drop material. The two regimes, characterized by certain quasistationary temperatures, are separated by a temperature interval featuring unstable states of the system. The particular realization of one or another quasistationary regime is determined by the initial temperature of the drop.
BACKGROUND:Ensuring the voltage balance of the neutral point of the DC link within acceptable limits is one of the mandatory requirements during the operation of a three-level autonomous neutral point clamped voltage source inverter. It is known that neutral point voltage imbalance can adversely affect the operation of the inverter and the load at all, lead to the failure of both power switches and capacitors in the DC link. Neutral point voltage imbalance mostly often occurs due to the asymmetry of the nominal values of DC capacitors, inconsistent properties of switching devices, asymmetric three-phase load, and also due to the imperfection of the converter control algorithm. AIMS:Selection of the optimal switching sequence that ensures the smallest deviation of the neutral point voltage and the number of switching of power switches in a three-level voltage source inverter. METHODS:For an objective comparison of the considered switching sequences and their influence on the neutral point voltage balance, a simulation model of a three-level neutral point clamped voltage source inverter was developed in theMATLAB/Simulinksoftware. To control this inverter, a space vector modulation method was used with three different switching sequences: five-segment, seven-segment and standard. RESULTS:The topology of a three-level neutral point clamped voltage source inverter is presented. The experimental dependencies of the neutral point voltage deviation error was taken with a change in the modulation coefficient, the frequency of the fundamental harmonic at the inverter output, and load characteristics for three different switching sequences. CONCLUSIONS:In this paper, the influence of the basic vectors and the influence of switching sequences on the neutral point voltage balance are studied. Combinations of states of large and zero basic vectors do not affect the neutral point voltage. For the medium basic vectors, the neutral point voltage can increase or decrease depending on the operating conditions of the inverter. The small basic vectors significantly affect the neutral point voltage. Considering the abovementioned, the seven-segment sequence that ensures both the optimal balance of the neutral point voltage and the level of switching losses should be considered as the best switching sequence for a three-level inverter.