Michal Ociepa

Mr. Michal Ociepa


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2018 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
MOMichal Ociepa
Michal Ociepa
MJMariusz Jenek
Mariusz Jenek
EFEugene Feldshtein
Eugene Feldshtein
This study presents the results of research on the condition of low content polycrystalline cubic boron nitride cutting tools (cBN-L) when finish turning of hardened AISI D2 tool steel. The least...

7 April 2021 in Coatings
Verified
Journal Article
Open access
PDF file
MOMichal Ociepa
Michal Ociepa
MJMariusz Jenek
Mariusz Jenek
eng. Piotr Kuryloeng. Piotr Kurylo
eng. Piotr Kurylo
The article presents the results of studying the effects of coated (TiN, TiAlN) and uncoated polycrystalline cubic boron nitride (PCBN) machining blades on the key geometric structure parameters of the surface of hardened and tempered EN X153CrMoV12 steel after finish turning. A comparative analysis of the use of coated and coated cutting tools in finish turning of hardened steels was made. Tool materials based on polycrystalline cubic boron nitride PCBN (High-CBN; Low-CBN) have been described and characterized. The advantages of using TiN and TiAlN-coated cutting tools compared to uncoated were demonstrated. The lowest influence of the feed on the values of all tested roughness parameters was noted for surfaces treated with TiN- and TiAlN-coated tools (both with 50 vol.% of CBN). For uncoated tools (60 vol.% of CBN) for feeds f = 0.2 and 0.3 mm/rev., the highest values of Ra and Rz roughness parameters were found. Moreover, the lack of protective coating contributed to the occurrence of intense adhesive wear on the flank surface, which was also in the range of the feed values f = 0.2 and 0.3 mm/rev. The analysis of material surface after treatment with the uncoated tools with the feed f = 0.2 mm/rev. showed the occurrence of the phenomenon of lateral material flow and numerous chip deflections.

1 July 2019 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
MOMichal Ociepa
Michal Ociepa
MJM. Jenek
M. Jenek
EFE. Feldshtein
E. Feldshtein
KLK. Leksycki
K. Leksycki
The study presents the results of an analysis of the phenomenon of material side flow during finish turning of EN X153CrMoV12 (H12MF GOST 5950-2000) tool steel hardened to 63 ± 2 HRC with cutting...

23 February 2021
Verified
Book Chapter
Closed access
PDF file
MOMichal Ociepa
Michal Ociepa
MJM. Jenek
M. Jenek
OYO. V. Yagolnitser
O. V. Yagolnitser

10 September 2018 in Mechanik
Verified
Journal Article
Open access
MOMichal Ociepa
Michal Ociepa
MJMariusz Jenek
Mariusz Jenek
MZMaria Zhbankova
Maria Zhbankova
The results of research on the influence of multi-layer CVD and PVD coatings on carbide cutting tools on selected parameters of the surface layer after finishing turning of C45 steel (1.0503) are described. The research showed a significant effect of antiwear coatings on the condition of surface layer. In the case of all tested blades, an increase in the strengthening level of the surface layer was noted along with the increase of the feed rate.