Mariusz Jenek

Dr. Mariusz Jenek


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 April 2021 in Coatings
Verified
Journal Article
Open access
PDF file
MOMichal Ociepa
Michal Ociepa
MJMariusz Jenek
Mariusz Jenek
eng. Piotr Kuryloeng. Piotr Kurylo
eng. Piotr Kurylo
The article presents the results of studying the effects of coated (TiN, TiAlN) and uncoated polycrystalline cubic boron nitride (PCBN) machining blades on the key geometric structure parameters of the surface of hardened and tempered EN X153CrMoV12 steel after finish turning. A comparative analysis of the use of coated and coated cutting tools in finish turning of hardened steels was made. Tool materials based on polycrystalline cubic boron nitride PCBN (High-CBN; Low-CBN) have been described and characterized. The advantages of using TiN and TiAlN-coated cutting tools compared to uncoated were demonstrated. The lowest influence of the feed on the values of all tested roughness parameters was noted for surfaces treated with TiN- and TiAlN-coated tools (both with 50 vol.% of CBN). For uncoated tools (60 vol.% of CBN) for feeds f = 0.2 and 0.3 mm/rev., the highest values of Ra and Rz roughness parameters were found. Moreover, the lack of protective coating contributed to the occurrence of intense adhesive wear on the flank surface, which was also in the range of the feed values f = 0.2 and 0.3 mm/rev. The analysis of material surface after treatment with the uncoated tools with the feed f = 0.2 mm/rev. showed the occurrence of the phenomenon of lateral material flow and numerous chip deflections.

1 June 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MJMariusz Jenek
Mariusz Jenek
PSPaweł Schlafka
Paweł Schlafka
The results presented in the dissertation show the influence of a kind and concentration of the flux added during the process of the lead brass smelting on its structure, chemical composition and mechanical properties—hardness and strength. A positive refining, structure, mechanical properties, brass influence of the refining and modification process manifested in an improvement of mechanical properties as well as an increase of the structure, chemical composition and mechanical properties homogeneity in the entire volume of the ingot has been proven. The influence of the flux concentration on the structure and mechanical properties of the alloy was determined. The optimal flux concentration improving the tested properties was established.

1 January 2022 in Rocznik Ochrona Środowiska
Verified
Journal Article
Closed access
MJMariusz Jenek
Mariusz Jenek
MOMichał Ociepa
Michał Ociepa
WWWaldemar Woźniak
Waldemar Woźniak
ŠVŠárka Vilamová
Šárka Vilamová
EŠEva Švecová
Eva Švecová
The article presents the research results on the influence of the PVD coating on the cutting tool on the surface roughness and energy consumption in the cast iron turning process. It was shown that using coated tools leads to obtaining a surface qualitatively corresponding to the ground surface and to reducing the power consumption of the machine tool. In addition, the process itself, carried out without a cooling and lubricating liquid, is more eco-friendly, as it excludes its use, disposal and negative environmental impact.

1 August 2024 in Journal of Achievements in Materials and Manufacturing Engineering
Verified
Journal Article
Closed access
MJMariusz Jenek
Mariusz Jenek
ADA.D. Dobrzańska-Danikiewicz
A.D. Dobrzańska-Danikiewicz
The work aimed to determine the possibility of replacing the grinding operation of Vanadis 4 Extra Super Clean and Vanadis 23 Extra Super Clean powder steels with a turning operation using PCBN cutting tools available on the market.The paper presents tribological properties test results of two kinds of hardened powder tool steels, i.e. Vanadis 4 Extra SuperClean and Vanadis 23 SuperClean, as well as Sverker 21 alloy steel after finish turning with coated and uncoated polycrystalline cubic boron nitride (PCBN) cutting tools. The tribological properties of the materials, including friction coefficient and wear intensity, were studied and analysed.The largest increase in wear intensity in the entire range of the tested loads was obtained for tribological pairs with samples treated with uncoated blades and TiAlN-coated blades, regardless of the type of material. The analysis showed that in the entire range of the tested tribological pair loading, Sverker 21 – X153CrMoV12 alloy steel, the highest values of the mean friction coefficient were obtained for the samples treated with uncoated blades and TiAlN coated blades. Different results were obtained during the research on the tribological properties of both powder steels. In the entire range of the tested load, the highest values of the average friction coefficient were obtained for the samples machined with TiN-coated blades.Despite the obvious advantages, hard machining of powder steels is not widely used in industry today. The reasons for the relatively low popularity of turning heat-treated materials, including powder steels, can be found in the still very high costs of PCBN tools, making it necessary to select optimal machining parameters and appropriate cutting tools to ensure production economic viability.The tool steels' tribological properties after finish turning using PCBN blades are similar to those properis obtained after the grinding process.The analysis showed the possibility of replacing the grinding process with finish turning using PCBN blades of steel tools. However, this process requires properly selecting the blade type suitable for the processed material.

10 February 2021 in Research Square
Verified
Preprint
Open access
PDF file
MJMariusz Jenek
Mariusz Jenek
PSPaweł Shlafka
Paweł Shlafka
The results presented in the dissertation show the influence of a kind and concentration of the flux added during the process of the lead brass smelting on its structure, chemical composition and mechanical properties – hardness and strength. A positive i refining, structure, mechanical properties, brassnfluence of the refining and modification process manifested in an improvement of mechanical properties as well as an increase of the structure, chemical composition and mechanical properties homogeneity in the entire volume of the ingot has been proven.

1 January 2024
Verified
Book
Closed access
UZUniwersytet Zielonogórski
Uniwersytet Zielonogórski
MJMariusz Jenek
Mariusz Jenek
Niniejsze opracowanie omawia wytyczne dotyczące niepewności pomiarowych i różnicę między niepewnością a błędem. Wskazuje, że pomiar zawsze jest obarczony pewną niepewnością, która wynika z ograniczeń przyrządów, metody pomiarowej i innych czynników. Opisuje metody obliczania niepewności w zależności od rodzaju pomiaru. Przedstawiono również podstawowe zagadnienia dotyczące podejmowania decyzji o zgodności wyrobu ze specyfikacją oraz podstawowe informacje związane z rozkładami statystycznymi wykorzystywanymi w metrologii. Wszystkie przedstawione zagadnienia zilustrowano licznymi przykładami, które w sposób praktyczny mają wyjaśnić przedstawiane w pracy zagadnienia.