Ibrahim Nouzil

Mr. Ibrahim Nouzil


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
Abdelkrem EltaggazAbdelkrem Eltaggaz
Abdelkrem Eltaggaz
INIbrahim Nouzil
Ibrahim Nouzil
Ibrahim DeiabIbrahim Deiab
Ibrahim Deiab
Minimum Quantity Lubrication nanofluid (MQL-nanofluid) is a viable sustainable alternative to conventional flood cooling and provides very good cooling and lubrication in the machining of difficult to cut materials such as titanium and Inconel. The cutting action provides very difficult conditions for the coolant to access the cutting zone and the level of difficulty increases with higher cutting speeds. Furthermore, high compressive stresses, strain hardening and high chemical activity results in the formation of a ‘seizure zone’ at the tool-chip interface. In this work, the impact of MQL-nanofluid at the seizure zone and the corresponding effects on tool wear, surface finish, and power consumption during machining of Ti-6Al-4V was investigated. Aluminum Oxide (Al2O3) nanoparticles were selected to use as nano-additives at different weight fraction concentrations (0, 2, and 4 wt.%). It was observed that under pure MQL strategy there was significant material adhesion on the rake face of the tool while the adhesion was reduced in the presence of MQL-nanofluid at the tool-chip interface, thus indicating a reduction in the tool chip contact length (TCCL) and reduced seizure effect. Furthermore, the flank wear varied from 0.162 to 0.561 mm and the average surface roughness (Ra) varied from 0.512 to 2.81 µm. The results indicate that the nanoparticle concentration and the reduction in the seizure zone positively influence the tool life and quality of surface finish.

6 August 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
INIbrahim Nouzil
Ibrahim Nouzil
Abdelkrem EltaggazAbdelkrem Eltaggaz
Abdelkrem Eltaggaz
Salman PervaizSalman Pervaiz
Salman Pervaiz
Ibrahim DeiabIbrahim Deiab
Ibrahim Deiab
The lubrication properties of nanoparticles are of great interest to the manufacturing industry and led to the development of the nano-minimum quantity lubrication (NMQL) cooling strategy. To evaluate the sustainability characteristics of nano-minimum quantity lubrication, apart from analyzing the benefits of increasing machining efficiency, it is also essential to evaluate the potential detrimental effects of nanoparticles on human health and the environment. Existing literature provides substantial data on the benefits of nano-minimum quantity lubrication machining. However, the current literature does not provide researchers in the machining sector a comprehensive analysis of the toxicity of the nanoparticles used in nano-minimum quantity lubrication. This study aims to provide a comprehensive review that addresses the toxicity levels of the most frequently used nanoparticles in NMQL machining. To understand the impacts of nanoparticles on the human body and the environment, in vitro studies that evaluate the nanoparticles’ toxicity on human cells and in vitro/in vivo studies on other living organisms are considered. The results from toxicity studies on each of the chosen nanoparticles are summarized and presented in chronological order. The reviewed studies indicate transition metal dichalcogenides (MoS2 and WS2) exhibit very low toxicity when compared to other nanoparticles. The toxicity of hBN and AL2O3 nanoparticles varies depending on their lengths and crystalline structures, respectively. In conclusion, a chart that maps the toxicity levels of nanoparticles on seven different human cell lines (human lung epithelial cells (A549), human bronchial epithelial cells (Nl-20), AGS human gastric cells, human epidermal cells (HEK), human liver-derived cells (HepG2), human endothelial cells and human peripheral cells), representing exposures by inhalation, ingestion and dermal contact, was developed for easy and quick insights. This is the first attempt in open literature to combine the results of the experimental investigations of nano-minimum quantity lubrication cooling and the toxicity studies of nanoparticles, allowing researchers to make informed decisions in the selection of the most sustainable nanoparticles in the nano-minimum quantity lubrication machining process.

16 July 2021
Verified
Preprint
Open access
INIbrahim Nouzil
Ibrahim Nouzil
Abdelkrem EltaggazAbdelkrem Eltaggaz
Abdelkrem Eltaggaz
Salman PervaizSalman Pervaiz
Salman Pervaiz
Ibrahim DeiabIbrahim Deiab
Ibrahim Deiab
Sustainability is the key indicator for environmental protection and socio-economic development of nations in the present world. The global importance of machining sector has prompted various studies to investigate optimum cooling and lubrication properties that maximize effectiveness while minimizing the adverse impact on the environment. Minimum Quantity Lubrication (MQL) with