Carbon-supported catalysts with atomically dispersed metal sites, also known as “single-atom catalysts (SACs)”, have attracted enormous attention for the oxygen reduction reaction (ORR) due to their theoretical maximal atom utilization and superior catalytic activity. Two common strategies to achieve high electrocatalytic performance for SACs are to enhance the intrinsic activity by modulating the electronic structure of active sites and to incorporate more single active sites by increasing the metal loading. In this review, we have summarized the key advances in ORR electrocatalysis of carbon-supported heterogeneous catalysts with atomically dispersed metal sites during the past decade, mainly focusing on the modulation of the electronic structure and the elevation of metal loading, and the operando/ex situ characterization techniques of the electronic structure evolution of SACs during the ORR process have also been highlighted. Meanwhile, the underlying formation mechanism of SACs has also been discussed in detail for both “bottom-up” and “top-down” approaches. Finally, the current challenges and future perspectives of carbon-supported SACs for ORR-related energy devices have been outlined. Hopefully, this timely review will provide an insightful roadmap for the future research of SACs.
Development of efficient metal-free electrocatalysts derived from biomass with high activity towards oxygen reduction reaction (ORR) has gained significance attention due to their low manufacturing cost, environmental friendliness and easy large-scale production. Hence, we present a facile method to prepare nitrogen-self-doped carbon aerogels (NSCAs) with a three-dimensional (3D) interconnected porous structure and large surface area. The sample is prepared via high-temperature pyrolysis using gelatin as precursor and sodium chloride (NaCl) as sacrificial template. The obtained NSCA-800 catalyst shows excellent ORR performance in O2-saturated alkaline electrolyte, which is comparable to a commercial Pt/C catalyst, in terms of its onset potential (0.92 V vs. RHE), half-wave potential (0.77 V vs. RHE), and limited current density (5.31 mA cm−2). Particularly, the NSCA-800 catalyst exhibits outstanding long-term stability, its ORR kinetic current still retains 95.7% after a continuous 4 h test while that for commercial Pt/C retains just 74.3%. The sustainable biomass gelatin is a promising precursor for the development of carbon materials as effective ORR catalysts.
In order to improve the impact toughness and wear resistance of the tool and die steels, this study innovatively prepared strengthened H13 steels with different contents of single-phase TiC and dual-phase TiC + TiB2 through in situ nanoparticle/Al master alloys at room temperature. The microstructure evolution and mechanical properties as well as wear resistance were investigated. Results indicate that the H13 steel with 0.02 wt.% dual-phase TiC + TiB2 nanoparticles has a more uniform and finer microstructure, and the mechanical properties and wear resistance are significantly improved. The yield strength, maximum tensile strength, breaking strain, uniform elongation, product of strength plasticity, and unnotched and U-notched impact toughness of H13 steel with 0.02 wt.% dual-phase TiC + TiB2 are higher than that of H13 steel. In addition, the volume wear rate, maximum scratch depth and width reach 7.1 × 10−11 m3/m, 6050 nm and 90 μm, respectively, which are reduced by 44.5%, 30.1% and 45.5% compared with that of H13 steel. Refining the microstructure and improving impact toughness and wear resistance of H13 tool steel through trace nanoparticles can provide important inspiration for industrial applications.
21 October 2014 in The International Journal of Advanced Manufacturing Technology
The material 36MnVS4 is the second generation of connecting rod fracture-split material. However, it generates more quality defects during the fracture-split process. To investigate the causes of defects that occurred, the material properties and fracture-split performance of the 36MnVS4 are researched and compared with C70S6. The fracture-split easily-induced defects are also analyzed. By finite element simulation and experimental analysis, the results show that the 36MnVS4 has lower carbon content and more ferrite, therefore the fracture surface of the 36MnVS4 connecting rod is more prone to tears and the plastic deformation range is greater. The fracture speed of the 36MnVS4 connecting rod is 20% lower than that of the C70S6 connecting rod. The slower fracture separation rate increases the possibility of defects generation. The crack initiation position of the 36MnVS4 connecting rod is random, scattered, and unstable, and the 36MnVS4 has higher gap sensitivity. Therefore, the 36MnVS4 connecting rod is more prone to produce quality defects in the fracture-split process. By changing the cross-section design, the outer edge of the joint surface is changed to arc-shaped, which can improve the fracture-split process of the 36MnVS4 connecting rod and reduce the processing defects.