Simultaneously improving the strength, toughness, and ductility of cast steels has always been a difficult problem for researchers. Biphase TiCx-TiB2 nanoparticle-reinforced cast steels are prepared by adding in situ nanosized biphase TiCx-TiB2/Al master alloy during the casting process. The experimental results show that a series of significant changes take place in the microstructure of the steel: the ferrite-pearlite structure of the as-cast steels and the bainite structure of the steels after heat treatment are refined, the grain size is reduced, and the content of nanoparticles is increased. Promotion of nucleation and inhibition of dendrite growth by biphase TiCx-TiB2 nanoparticles leads to a refinement of the microstructure. The fine microstructure with evenly dispersed nanoparticles offers better properties [yield strength (1246 MPa), tensile strength (1469 MPa), fracture strain (9.4%), impact toughness (20.3 J/cm2) and hardness (41 HRC)] for the steel with 0.018 wt.% biphase TiCx-TiB2 nanoparticles, which are increased by 15.4%, 31.2%, 4.4%, 11.5%, and 7.9% compared with the 40Cr steels. The higher content of nanoparticles provides higher strengths and hardness of the steel but are detrimental to ductility. The improved properties may be attributed to fine grain strengthening and the pinning effect of nanosized carbide on dislocations and grain boundaries. Through this work, it is known that the method of adding trace (0.018 wt.%) biphase TiCx-TiB2 nanoparticles during casting process can simultaneously improve the strength, toughness, as well as ductility of the cast steel.
In the general environment of lightweight automobiles, the integrated die-casting technology proposed by Tesla has become the general mode to better achieve weight reduction in automobiles. The die-casting mold required by integrated die-casting technology has the characteristics of large scale and complexity. Hence, higher requirements are put forward for the comprehensive performance of the die steel. Despite the stagnation in the progress of conventional strengthening methods, enhancing the performance of die steel has become increasingly challenging. Indeed, it necessitates exploring novel die steel and optimizing heat treatment and reinforcement technologies. This article summarizes and analyzes the development status of die steel and corresponding heat treatment and microstructure manipulation as well as strengthening methods and elaborates on an excellent nano-strengthening technology. Furthermore, this review will aid researchers in establishing a comprehensive understanding of the development status of die steel and the processes utilized for its strengthening. It will also assist them in developing die steel with improved comprehensive performance to meet the high demand for mold steel in the integrated die-casting technology of the new era.
Bimodal hybrid in-situ nano-/micro-size TiC/Al composites were prepared with combustion synthesis of Al-Ti-C system and hot press consolidation. Attempt was made to obtain in-situ bimodal-size TiC particle reinforced dense Al matrix composites by using different carbon sources in the reaction process of hot pressing forming. Microstructure showed that the obtained composites exhibited reasonable bimodal-sized TiC distribution in the matrix and low porosity. With the increasing of the carbon nano tube (CNT) content from 0 to 100 wt. %, the average size of the TiC particles decreases and the compressive strength of the composite increase; while the fracture strain increases first and then decreases. The compressive properties of the bimodal-sized TiC/Al composites, especially the bimodal-sized composite synthesized by Al-Ti-C with 50 wt. % CNTs as carbon source, were improved compared with the composites reinforced with single sized TiC. The strengthening mechanism of the in-situ bimodal-sized particle reinforced aluminum matrix composites was revealed.
As an important part of die steels, hot-work die steels are mainly used to manufacture molds made of solid metal or high-temperature liquid metal from heating to recrystallization temperature. In view of the requirements for mechanical properties and service life for hot-work die steel, it is conducive to improve the thermal fatigue resistance, wear resistance, and oxidation resistance of hot work die steel. In this review, the main failure modes of hot-work die steel were analyzed. Four traditional methods of strengthening and toughening die steel were summarized, including optimizing alloying elements, electroslag remelting, increasing the forging ratio, and heat treatment process enhancement. A new nano-strengthening method was introduced that aimed to refine the microstructure of hot-work abrasive steel and improve its service performance by adding nanoparticles into molten steel to achieve uniform dispersion. This review provides an overview to improve the service performance and service life of hot work die steel.
In order to improve the impact toughness and wear resistance of the tool and die steels, this study innovatively prepared strengthened H13 steels with different contents of single-phase TiC and dual-phase TiC + TiB2 through in situ nanoparticle/Al master alloys at room temperature. The microstructure evolution and mechanical properties as well as wear resistance were investigated. Results indicate that the H13 steel with 0.02 wt.% dual-phase TiC + TiB2 nanoparticles has a more uniform and finer microstructure, and the mechanical properties and wear resistance are significantly improved. The yield strength, maximum tensile strength, breaking strain, uniform elongation, product of strength plasticity, and unnotched and U-notched impact toughness of H13 steel with 0.02 wt.% dual-phase TiC + TiB2 are higher than that of H13 steel. In addition, the volume wear rate, maximum scratch depth and width reach 7.1 × 10−11 m3/m, 6050 nm and 90 μm, respectively, which are reduced by 44.5%, 30.1% and 45.5% compared with that of H13 steel. Refining the microstructure and improving impact toughness and wear resistance of H13 tool steel through trace nanoparticles can provide important inspiration for industrial applications.