In this study, influence of crystal structure and chemical composition for Silico-Ferrite of Calcium and Aluminum (SFCA) on its reducibility are examined. Eight types of powder samples containing SFCA and SFCA-I were prepared using chemical reagents by the heat treatments in air. The samples were heated up to 800°C in the different atmospheres of CO-CO2-H2-H2O systems. The reducibility of the samples was evaluated using the peak intensity ratio identified by XRD before and during the reduction experiment. The intensity of SFCA peak is not decreased up to 700°C in CO-CO2 atmosphere, whereas the intensity become weak in CO-CO2-H2-H2O atmosphere. The intensity of SFCA-I peak is decreased above 500oC in all atmospheric condition and the reduction reactions are enhanced by the addition of H2-H2O gas. Decrease in intensity of SFCA peak is independent of Fe composition, whereas that of SFCA-I is decreased with decreasing Fe concentration. The difference in reducibility is attributed to the difference in the crystal structure of multi-component CF. SFCA and SFCA-I are composed of pyroxene and spinel units. Since the pyroxene unit contains more gangue minerals than spinel unit, it implies that the pyroxene unit shows low reducibility than the spinel units. Since SFCA-I contains more the spinel units than SFCA, SFCA-I is easily reduced than SFCA.
Currently, the Japanese steel industry is developing the technologies to reduce 30% of domestic CO₂ emissions from iron- and steelmaking industry using an innovative ironmaking process such as the COURSE50 project, which focuses on H2 reduction and CCUS technologies. On the other hand, it has been reported that an increasing H2 gas ratio in the blast furnace reducing gas promotes the low temperature reduction disintegration of the iron ore pellet. In this study, the low temperature reduction disintegration mechanism of self-fluxing pellet under higher hydrogen condition at 500°C was examined. During hydrogen reduction which proceeds uniformly, the fine cracks with few micrometers in the primary particles form. It leads to the formation of fine particles with the size of less than 0.1 mm on the surface of the pellet. Increase in the particles with few millimeters makes a significant impact on the permeability of the blast furnace. On the other hand, CO reduction without hydrogen gas proceeds topochemically, and volumetric fracture progresses with generation of the cracks with several millimeters in length due to the stress difference between near the surface and in the center of pellet. Under higher H2 conditions, reduction proceeds uniformly, so such cracks causing volume fractures are hard to form, but the finer cracks are easier formed than the case of CO reduction, and the amounts of finer particles increases.
Synopsis : Carbonization behavior of biomass in the rapid carbonization/pulverized process using heat storage materials was experimentally examined. Biomass samples were charged into a rotary kiln-type electric furnace with stainless balls. Obtained biomass chars were evaluated by means of gasification test in CO 2 atmosphere using a thermal gravimetry. The char was classified into two type, "fine" and "coarse", by particle size. "Coarse" char contracted with increasing holding temperature. Crashing of biomass char was observed at the holding temperatures over 600°C and fine char was formed. Melted structure was observed on the surface of "coarse" char indicating rapid heating. Yields of the total char are decreased with increasing holding temperature due to vaporization of volatile matters like tar. On the other hand, the yield of "fine" char is increased with increasing rotation speed when carbonization reaction sufficiently proceeded. The char obtained by the present carbonization experiment at between 600 and 800°C for 10 min showed similar gasification property with CO 2 to that prepared by normal carbonization at 800°C for 1 h.
For decreasing carbon dioxide emission from iron- and steelmaking industry, hydrogen utilization in the blast furnace has been considered. Iron ore sinter is one of the major iron sources for the blast furnace. It is known that the effects of the hydrogen concentration in the reducing gas on the reducibility and reduction disintegration of the sinter are strong. In this study, the evaluation of the mineral phase of the Mosaic EmBedding Iron Ore Sintering (MEBIOS) sinter and reducibility using a laboratory scale furnace simulated the blast furnace condition with high hydrogen concentration and the experimental blast furnace were carried out.MEBIOS sinter has higher ratio of the mineral phases, i.e., hematite and acicular calcium ferrite with primary hematite, showing higher reducibility compared to the conventional sinters. The value of JIS-RDI of the MEBIOS sinter decreases with an increase in that of JIS-RI, which is the reverse trend of the conventional sinter. Further, the basket charge test with the experimental blast furnace confirmed that the MEBIOS sinter shows high reducibility under the condition of high hydrogen concentration while the reduction disintegration behavior at low temperature is similar to conventional sinter.
It has been reported that an increasing H2 gas ratio of the reducing gas in the blast furnace promotes the low temperature reduction disintegration of the iron ore pellet. Reduction of the pellet sample proceeds uniformly under higher H2 condition at 500°C. Microcracks with the size of several micrometer form at the primary particles of iron oxide and it promote fine particles formation after the drum test. Macrocracks with the size of several millimeter form inside of the pellet after reduction and it promotes the volumetric destruction. In this study, the temperature dependence of reduction disintegration of self-fluxing pellet under higher H2 condition was examined.Pellet sample was reduced under CO and CO-H2 gas conditions at 600°C and 700°C. After reduction, the disintegration test was conducted using the drum. Under higher H2 condition at 600°C, the density of microcracks decreases with increasing reduction degree and it leads to lower of the RDI value than that at 500°C. The reason is that the volumetric expansion by the reduction from hematite to magnetite at 600°C is not significant compared with that at 500°C. The difference of reduction degree at the center and near the surface of the pellet increases with increasing the reduction temperature. Reduction reaction proceeds more topochemically by increasing reduction temperature and the addition of hydrogen. This change leads the macrocrack formation, which is same mechanism under CO gas condition at 500°C. At 700°C, on the other hand, this microcrack was not observed because the volumetric expansion by the reduction is lower than that at lower temperature. Therefore, the effect of hydrogen addition on disintegration is not significant at 700°C.