In present study, novel nitrogen doped carbon dots (NCDs) are synthesized using a green material—dopamine—as a precursor and studied as corrosion inhibitors for Q235 carbon steel in 1 M HCl solution. According to the electrochemical results, it is found that NCDs acting as a mixed-type corrosion inhibitor can effectively retard the acid corrosion of carbon steel, and their inhibition efficiency increases with the concentration increasing from 50 to 400 ppm. The highest inhibition efficiency is 96.1% in the presence of 400 ppm NCDs at room temperature. Additionally, the adsorption of NCDs obeys the Langmuir adsorption isotherm. In addition, weight loss results show that the inhibition efficiency in the presence of 400 ppm NCDs increases with prolonged exposure time and rising temperature (298–328 K), owing to the strong adsorption of NCDs on the steel surface, and the η value is 92.2% at 60 h of immersion and 86.2%, 89.1%, 90.6% and 92.9% at 298, 308, 318 and 328 K, respectively. Surface analysis by scanning electron microscope (SEM), laser scanning confocal microscope (LSCM) and X-ray photoelectron spectroscopy (XPS) further proves the formation of a protective NCD film on the steel surface.
Novel nitrogen and sulfur co-doped carbon dots (N,S-CDs) were synthesized via a hydrothermal procedure using citric acid (CA) and thiourea (TU) as precursors, and the corresponding corrosion protection performance was first investigated for Q235 carbon steel in 1 M HCl solution. Experimental results indicated that N,S-CDs as mixed-type corrosion inhibitors could effectively prevent Q235 carbon steel from corrosion in 1 M HCl solution, and the corrosion inhibition efficiency was improved with the increase in N,S-CD concentration. The maximum value was achieved at 400 ppm of N,S-CDs at 25 °C, which was approximately 96.6%, 94.6% and 90.55%, according to the potentiodynamic polarization curves, EIS results and weight loss measurement, respectively. Additionally, with the temperature ranging from 25 to 55 °C, the inhibition efficiency obtained from the weight loss measurement was enhanced from 90.55% to 94.04%. Such superior inhibition effect was assigned to the physisorption and chemisorption of N,S-CDs on the Q235 carbon steel surface, which was also be confirmed by XPS analysis. The adsorption of N,S-CDs onto a steel substrate conformed to the Langmuir adsorption isotherm.
In this study, to achieve a homogeneous dispersion of nanodiamond (ND) in a polyimide (PI) matrix and a strong interfacial adhesion between ND and the PI matrix, a biomimetic nondestructive dopamine chemistry was employed for surface modification of ND. FTIR and Raman spectroscopy studies revealed that self-polymerization of dopamine could produce thinner polydopamine (PDA) layers on the ND surface via spontaneous oxidation and the intermolecular cross-linking reaction of PDA molecules. The structure and morphology of PDA–ND were studied by FTIR, SEM, and Raman spectroscopy, which verified the π–π interactions between PDA and ND. The facile dispersion of PDA–ND in a polyamic acid prepolymer made it possible to obtain PI/ND composites with no obvious ND aggregation. The effect of PDA–ND nanoparticles on the thermal, mechanical and tribological properties of the resulting PI/PDA–ND composites were evaluated, and the results showed that the incorporation of PDA–ND could increase the hardness, tensile strength, storage modulus, as well as the wear resistance properties. PI/PDA–ND composites prepared in this study showed that PDA–ND is a promising nanoreinforcing filler for PI composites.
As a structural analogue of graphene, hexagonal boron nitride (h-BN) is receiving increased attention in the field of anticorrosive polymer coatings due to its electrical insulation and high barrier properties. However, the hydrophobicity of h-BN nanosheets makes them easily aggregate in water, thereby limiting their application in water-borne polymer coatings for corrosion protection. In this study, carbon dots (CDs) derived from citric acid are prepared as a dispersant for improving the dispersion of h-BN nanosheets in a water-borne epoxy (WEP) coating by taking advantage of the π–π interaction between h-BN and CDs. The possible reaction between oxygen functional groups on the CD surface and unreacted epoxy resin/curing agent could increase the compatibility and crosslinking density between h-BN and the WEP matrix, which in turn effectively reinforces the barrier effect of the composite coating. EIS results show that the impedance modulus of the h-BN@CDs/WEP coating is higher than 108 Ω cm2 after 34 d of exposure in 3.5 wt% NaCl solution, nearly three orders of magnitude higher than those of pure WEP and h-BN/WEP (∼105 Ω cm2). Additionally, salt spray and LEIS results reveal the superior corrosion protection performance of the h-BN@CDs/WEP coating even under damaged status.