In present study, novel nitrogen doped carbon dots (NCDs) are synthesized using a green material—dopamine—as a precursor and studied as corrosion inhibitors for Q235 carbon steel in 1 M HCl solution. According to the electrochemical results, it is found that NCDs acting as a mixed-type corrosion inhibitor can effectively retard the acid corrosion of carbon steel, and their inhibition efficiency increases with the concentration increasing from 50 to 400 ppm. The highest inhibition efficiency is 96.1% in the presence of 400 ppm NCDs at room temperature. Additionally, the adsorption of NCDs obeys the Langmuir adsorption isotherm. In addition, weight loss results show that the inhibition efficiency in the presence of 400 ppm NCDs increases with prolonged exposure time and rising temperature (298–328 K), owing to the strong adsorption of NCDs on the steel surface, and the η value is 92.2% at 60 h of immersion and 86.2%, 89.1%, 90.6% and 92.9% at 298, 308, 318 and 328 K, respectively. Surface analysis by scanning electron microscope (SEM), laser scanning confocal microscope (LSCM) and X-ray photoelectron spectroscopy (XPS) further proves the formation of a protective NCD film on the steel surface.
Graded cellular material is a superb sandwich candidate for blast alleviation, but it has a disadvantage for the anti-blast design of sacrificial cladding, i.e., the supporting stress for the graded cellular material cannot maintain a constant level. Thus, a density graded-uniform cellular sacrificial cladding was developed, and its anti-blast response was investigated theoretically and numerically. One-dimensional nonlinear plastic shock models were proposed to analyze wave propagation in density graded-uniform cellular claddings under blast loading. There are two shock fronts in a positively graded-uniform cladding; while there are three shock fronts in a negatively graded-uniform cladding. Response features of density graded-uniform claddings were analyzed, and then a comparison with the cladding based on the uniform cellular material was carried out. Results showed that the cladding with uniform cellular materials is a good choice for the optimal mass design, while the density graded-uniform cladding is more advantageous from the perspective of the critical length design indicator. A partition diagram for the optimal length of sacrificial claddings under a defined blast loading was proposed for engineering design. Finally, cell-based finite element models were applied to verify the anti-blast response results of density graded-uniform claddings.
Expanding ring experiment is an important method for dynamic fragmentation of solid under 1D tensile loading. Based on the split Hokinson pressure bar (SHPB), a liquid-driving experimental technology was developed for conducting expanding ring tests. The loading fixture includes a hydraulic cylinder filled with water, which is pushed by a piston connected to the input bar. As the water is driven, it expands the metallic ring specimen in the radial direction. The approximately incompressible property of the water makes it possible to drive the specimen in very high radial velocity by low velocity movement of piston, according to the large sectional area ratio of the cylinder to specimen. Using liquid-driving expanding ring device, 1060 aluminum rings (ductile materials)/PMMA rings (brittle materials) were fragmented and the fragments were recovered. Impact deformation of free-flying fragments was avoided through the use of “sample soft-capture” technology. The fragmentation process was observable by high speed camera through modifying the driving direction of the water. From the observations of the fracture morphology and the residual internal cracks of the recovered fragments, it is concluded that the fracture of the rings is caused by the circumferential tensile stress.
27 June 2023 in Mechanics of Advanced Materials and Structures
Compressive and tensile properties of a carbon nanotube (CNT) reinforced 2024Al composite are investigated under quasi-static and dynamic compression as well as quasi-static tension, along three different directions (extrusion, normal and transverse directions). Upon compression, yield and fracture strengths of the composite show negligible strain rate effect and mechanical anisotropy as manifested in the compressive stress–strain curves. Fractography and profilometry show that fracture surfaces are rough shear fracture planes for quasi-static compression; however, smooth conical fracture surfaces are observed for dynamic compression as a result of more homogeneous damage nucleation and growth, leading to high ductility under high strain rate loading. Pronounced mechanical anisotropy is observed for the composite under quasi-static tensile loading. Ductility or fracture strain is the highest along the normal direction, because debonding along the particle and lamellar interfaces is suppressed along this direction. In situ optical imaging along with digital image correlation is utilized to obtain the deformation dynamics of the composite along the three different directions. Stripe-shaped strain localizations appear in the strain fields along the extruded and tangential directions, while the strain fields are approximately uniformly distributed along the normal direction, consistent with the stress–strain curves.
When a brittle thin rod, such as a dry spaghetti stick, is bent beyond its flexural limit, it often breaks into more than two pieces, typically three or more. This phenomenon and puzzle has aroused widespread interest and discussion since its first proposal by Feynman. Previous work has partly explained the inevitability of the secondary fracture, but without any adjustable time parameter. In order to further understand this problem, especially the secondary fracture, in this paper we propose and study the dynamics of a half-infinite model to mimic the physics that a spaghetti stick is half-infinite under uniform bending. When the breaking process starts, a gradual release of initial moment of a linearly declining time at the free end, instead of a sudden release, is adopted, resulting in the introduction of a characteristic time parameter to the model and agrees better with the real situation. A specific analytical solution in terms of the excited bending moment using Euler–Bernoulli beam theory is derived, and that the gradual release of initial moment induces a burst of flexural waves, and these flexural waves locally increase the moment in the stick and progressively get to the maximum value, and then lead to the secondary fracture are concluded. The excited moment increases with time and distance, and has an asymptotic extremum value of 1.43 times initial moment. The gradual release in our model requires and gives certain distance and time when the excited bending moment reaches its extremum value, which provides a possibility to predict the detailed fracture parameters such as fragmentation length and time and thus to further understand the secondary fracture during spaghetti bent break.