Mayank Anand

Dr. Mayank Anand


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2018 in Tribology International
Verified
Journal Article
Open access
BPB. Pinedo
B. Pinedo
MHM. Hadfield
M. Hadfield
ITI. Tzanakis
I. Tzanakis
MCM. Conte
M. Conte
MAMayank Anand
Mayank Anand

1 July 2015 in Wear
Verified
Journal Article
Open access
MAMayank Anand
Mayank Anand
MHM. Hadfield
M. Hadfield
Jose L. ViescaJose L. Viesca
Jose L. Viesca
BTB. Thomas
B. Thomas
Antolin Hernández BattezAntolin Hernández Battez
Antolin Hernández Battez
SAS. Austen
S. Austen
In recent years, several papers have been published that investigate the potential use of ionic liquids (ILs) as additives in lubricants. However, corrosive attack of ILs on lubricated metal surfaces and low miscibility of ILs in the non-polar oils are major obstacles to maintaining an optimum lubrication performance level. High miscibility and no corrosive behaviour of Trihexyltetradecyl phosphonium bis(2,4,4-tri-methylpentyl) phosphinate and Trihexyltetradecyl phosphonium bis(2-ethylhexyl) phosphate, as lubricating oil additives have recently been described in literature. This article presents work on using these phosphonium based ILs as an additive in the fully formulated diesel engine lubricants. This approach could allow the used lubricants to recover their tribological performance for further use at the end of service life. This extension of service life has the potential to generate significant economic and environmental benefits. Also it will add to the much needed knowledge about the effect of interaction between ILs and existing additives in engine-aged lubricants on the tribological performance of ring-liner tribo-system of diesel engines. Results revealed an improvement in friction and antiwear performance of used lubricant by addition of both ILs. However an increase in wear was noted for new (fresh) and in-service lubricant samples. An interesting interference between existing lubricant additives and added ILs in a boundary film formation process has been observed


17 March 2016 in Lubricants
Verified
Journal Article
Open access
PDF file
Jose L. ViescaJose L. Viesca
Jose L. Viesca
MAMayank Anand
Mayank Anand
DBDavid Blanco
David Blanco
AFAlfonso Fernández-González
Alfonso Fernández-González
AGA. García
A. García
MHMark Hadfield
Mark Hadfield
This paper studies 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl) trifluorophosphate ionic liquid ([BMP][FAP]) as a 1 wt% additive to a polyalphaolefin (PAO 6) in the lubrication of CrN and TiN PVD coatings. Friction and wear behaviour were determined by using a ball-on-plate reciprocating tribometer at two loads (20 and 40 N) and a reciprocating frequency of 10 Hz. The tribological behaviour of this mixture has also been compared to a traditional oil additive, like zinc dialkyldithiophosphate (ZDDP). As an additive, ionic liquid exhibited an important friction and wear reduction compared to the base oil. However, tests conducted with ZDDP show slightly better results. XPS was used to analyse wear surfaces. The interactions of each additive with the surface contributed to improving the tribological behaviour of the lubricants.

1 October 2017 in Wear
Verified
Journal Article
Open access
MAMayank Anand
Mayank Anand
GBG. Burmistroviene
G. Burmistroviene
Ignacio Tudela-MontesIgnacio Tudela-Montes
Ignacio Tudela-Montes
RVR. Verbickas
R. Verbickas
GLG. Lowman
G. Lowman
YZYi Zhang
Yi Zhang
The multiple pass scratch test method was employed for characterising the tribological performance of soft metallic multilayer coatings under the linear sliding wear situation. For this purpose, three different structures of tin (Sn) based coating (<15Hv0.03) were produced by electroplating process on relatively hard metallic substrates (117Hv0.1). The coating structures studied include a benchmark monolayer coating with soft Sn matrix, and two multilayer coatings with 3-layers and 5-layers of soft Sn matrix and hard SnNi intermetallic sublayer (s). The test method involves sliding a 100Cr6 steel ball against the Sn coated surface under loaded condition for a certain length and then repeating the process 50 times in a unidirectional cyclic manner. Various loading conditions were applied to identify the correct load in order to eliminate the influence of surface roughness of coating and hardness of substrate on the tribological results. Finally, load of 10 N allowed the ball probe to remove a small amount of the coating material in each scratch cycle and differentiate between the characteristic friction and wear behaviour of different coating structures layer-by-layer. Post-test surface and cross-section of worn coating regions were analysed, and the scratch and Vickers hardness of fresh coating surfaces were measured, to correlate the tribological behaviour with the respective coating structure. Results clearly showed the beneficial effects of the lubricious intermetallic sublayer within 3-layers and 5-layers Sn coating structures. The improvement in performance was even higher with lesser thickness of sublayers in 5-layers structure. Apparently, the hard intermetallic sublayer strengths the multilayer structure and at the same time enhances its wear resistance due to increase in the overall hardness of coating. Therefore, the multiple pass scratch test method successfully compared the tribological performance of soft Sn based coatings under the carefully selected test conditions

30 May 2016 in Lubricants
Verified
Journal Article
Open access
PDF file
MAMayank Anand
Mayank Anand
MHMark Hadfield
Mark Hadfield
Jose L. ViescaJose L. Viesca
Jose L. Viesca
BTBen Thomas
Ben Thomas
RGRubén González
Rubén González
Antolin Hernández BattezAntolin Hernández Battez
Antolin Hernández Battez
The reduction of friction and wear losses in boundary lubrication regime of a piston ring-cylinder liner tribo-system has always been a challenge for engine and lubricant manufacturers. One way is to use lubricant additives, which can form boundary film quickly and reduce the direct contact between asperities. This article focuses on the assessment of boundary film forming behavior of two phosphonium-based ionic liquids (ILs) as additives in engine-aged lubricant to further improve its film forming capabilities and hence reduce friction and wear of contacting surfaces. A reciprocating piston ring segment-on-flat coupon under fully flooded lubrication conditions at room temperature (approx. 25 °C) was employed. The trihexyltetradecyl phosphonium bis(2-ethylhexyl) phosphate and trihexyltetradecyl phosphonium bis(2,4,4-tri-methylpentyl) phosphinate ionic liquids were used as additives in 6 vol. % quantity. Benchmark tests were conducted using fully formulated new lubricant of same grade (with and without ILs). Results revealed that the addition of phosphonium ILs to engine-aged lubricant led to quicker initiation of boundary film forming process. In addition, friction and wear performance of engine-aged lubricant improved by the addition of both ILs and these mixtures outperformed the fresh fully formulated oil. Chemical analysis showed higher concentration of phosphorus element on the worn surface indicating presence of ILs in the formed tribofilms.