This article analyzes the temperature data obtained for an aluminum alloy face milled using four different cutting strategies. The workpiece temperature was measured at six points with K-type thermocouples. The heat transfer taking place in the cutting zone was also simulated numerically using the finite element method (FEM) and the finite difference method (FDM). The calculation results concerning the distribution of temperature on the workpiece surface were compared with the experimental data. The numerically simulated distribution of temperature on the workpiece surface after face milling was considered in relation to the surface flatness. The findings suggest that the flatness deviations at the workpiece ends were dependent on the depth of cut. Another reason was the cutting strategy selected for the specific thermophysical properties of the workpiece material. Measurement of the workpiece temperature is extremely important because of the thermoelastic behavior and thermal expansion of the material. The isotropic properties of the aluminum alloy make it expand in all directions during milling.

The article presents the results and process analysis of the face milling of aluminium alloy 2017A with the CoroMill 490 tool on an AVIA VMC 800 vertical milling centre. The study analysed the effects of the cutting speed, the feed rate, the actual number of teeth involved in the process, the minimum thickness of the cut layer (h_min), and the relative displacement in the tool-workpiece system D(ξ) on the surface roughness parameter Ra. To measure relative displacement, an original bench was used with an XL-80 laser interferometer. The analysis of relative displacement and surface roughness allowed these factors to be correlated with each other. The purpose of this article is to determine the stable operating ranges of the CoroMill 490-050Q22-08M milling head with respect to the value of the generated relative displacement w during the face-milling process and to determine its influence on surface roughness. The research methodology presented in this paper and the cutting tests carried out allowed the determination of the optimum operating parameters of the CoroMill 490-050Q22-08M tool during the face milling of aluminium alloy 2017A, which are v_c 300 m/m and f_z—0.14 mm/tooth. Working with the defined cutting parameters allows all the cutting inserts in the tool body to be involved in shaping the geometrical structure of the surface, while maintaining a low vibration level D(ξ) > 1 µm, a low value of the parameter h_min > 1.5 µm, and the desired value of the parameter Ra > 0.2 µm

This article discusses experimental results concerning the quality of through holes drilled in Inconel 718. The tests involved hole cutting under 27 different conditions using different values of the feed per revolution and spindle speed, and different types of kinematic system. The drilling was performed on a CTX Alpha 500 universal turning center using tools with internal coolant supply. Three kinematic systems were considered for hole cutting. The first, based on the driven tool holder, had a stationary workpiece and a rotating and linearly fed tool. In the second, where drilling was based on the spindle rotations, the workpiece rotated while the tool moved along a straight line. In the third system, the workpiece and the tool rotated in opposite directions; the tool also performed a linear motion. The study aimed to assess the quality of holes on the basis of the following output parameters: the hole diameter, cylindricity and straightness errors, and the surface texture. A multifactorial statistical analysis was used to determine how the hole quality was dependent on the process parameters and the type of drilling kinematics. The findings confirm that the kinematic system, as well as the feed per revolution, are the key factors affecting the quality of holes drilled in Inconel 718. The analysis of the hole drilling process for Inconel 718, performed using a CNC turning center, shows that the third kinematic system was the best option as all the four parameters describing the hole quality had the lowest values. The best results were obtained in the 6th (n = 637 rpm, f_n = 0.075 mm/rev, KIN III) and 8th experiments (n = 955 rpm, f_n = 0.075 mm/rev, KIN II), because the parameters were then the lowest, with the scatter of results being up to 30%.

Efficient detection and rectification of metal components conditions during manufacturing and post-processing manufacturing are crucial for quality control in industries. This paper describes a lab-scale integrated system for real-time and auto-mated metal edge image detection using YOLOv5...

The physicochemical conditions of the siliconizing and boron–siliconizing processes of molybdenum-based alloys in a closed reaction space in an environment of chlorine and fluorine at reduced pressure were studied. Theoretical calculations of the equilibrium composition of systems with the participation of silicon, boron, molybdenum, nitrogen, oxygen, chlorine, and fluorine were carried out, which made it possible to determine the influence of process parameters (temperature, composition of the reaction medium) on the probable phase composition of the obtained coatings. Based on thermodynamic calculations, the composition and rational consumption of the initial powders and the temperature intervals of the chemical heat treatment (CHT) during the complex saturation of molybdenum-based alloys with silicon and boron were modeled. It was established that it is advisable to use chlorine as an activator, which leads to the formation of molybdenum chlorides MoCl₄ and MoCl₃ in the composition of the gas phase and can indicate the flow of exchange reactions between chlorides and the matrix of the processed material in the reaction space. The rational saturation temperature of alloys based on molybdenum with silicon and boron is determined—1100–1250 °C. The possibility of the existence of condensed phases MoSi₂, MoB_2.15, B₆Si, MoB_1.65, and MoB is shown.

This article presents an approximately model that allows for the determination of the maximum temperature of the chip surface in dry orthogonal turning. The mathematical formula describing the maximum temperature of the chip surface was formulated based on experimental data. The experiments were carried out for orthogonal cutting of austenitic steel AISI 321 with flat rake face carbide inserts that were made of tungsten carbide H10F, both uncoated and coated, with coatings of varied arrangement. Thermographic images of the cutting zone were used to verify the correctness of the approximately model. The obtained results show good agreement between the modelling results and experimental studies. The discrepancy of the maximum temperature values of the top surface of the chip does not exceed 6.4%.