A comparative study is made of the changes caused to the microstructure of anodic films by traditional hydrothermal sealing (HTS) and cold sealing (CS) processes, using the scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. SEM and TEM make it possible to visualize the different stages of the very complex sealing and aging mechanism of aluminum anodic oxide coatings indirectly determined by other techniques, showing evidence of the hexagonal structure of anodic coatings, plugging of the pore mouth with the formation of acicular pseudobohemite and the intermediate sublayers in HTS. It is also possible to verify, both in the coatings resulting from CS and in those subjected to HTS, the stages of dissolution-precipitation, with prior enlargement of the pore diameter and subsequent plugging of the entire pore length. For its part, electrochemical impedance spectroscopy (EIS) provides precise information on the effects of the aging process of anodic layers and their persistence over years and decades.
Commercially available oxidized (carboxylic groups) and nonoxidized multiwalled carbon nanotubes were studied as adsorbents of cerium(III) in batch operation mode. Several variables affecting the rare earth adsorption were investigated, including: the stirring speed applied to the system, the pH of the solution, and the metal concentration and carbon dosages. Although the removal of cerium from the solution is different and dependent upon the adsorbent type—(i) adsorption in nonoxidized multiwalled carbon nanotubes, (ii) cation exchange in the case of using oxidized multiwalled carbon nanotubes—the adsorption kinetics, the rate law and the isotherm models are the same for both adsorbents: pseudo-second order, film diffusion, and Langmuir Type-1, respectively. Cerium is desorbed from loaded adsorbents using acidic solutions.
A process aimed at the recovery of terbium from liquid solutions using activated carbon (AC) derived from spent coffee grounds (SCG) was assessed. AC was obtained using the hydro-alcoholic treatment of SCG, followed by the physical activation of the as-obtained product. The AC exhibited both microporous and mesoporous structures, which were shown by the corresponding nitrogen adsorption–desorption isotherms and scanning electron microscopy (SEM) images. In addition, a certain graphitic character was found in the micro-Raman measurements. By use of this AC, terbium adsorption was investigated, and the influence of solution pH, temperature, and the adsorbent amount on terbium uptake was tested. In addition, adsorption isotherms and kinetic studies were also evaluated. The best fit was found for the type-1 Langmuir isotherm and pseudo-second-order kinetics model. Thermodynamic studies revealed that terbium adsorption is an endothermic and spontaneous process. Terbium desorption by the use of acidic solutions was also investigated. This work demonstrated that it is possible to recover this valuable metal from liquid solution using the present AC.
The preparation of a low-cost cellulose-based bioadsorbent from cellulosic material extracted from rose stems (CRS) was carried out; rose stems are considered agricultural waste. After the required pretreatment of this waste and further treatment with an acidic mixture of acetic and nitric acids, the CRS product was produced. The resulting bioadsorbent was characterized by several techniques, such as X-ray diffraction, which revealed diffraction maxima related to the cellulose structure, whose calculated crystallinity index (CrI) was 75%. In addition, Fourier Transform Infrared spectroscopy (FTIR), 13C Nuclear Magnetic Resonance (NMR), and X-ray Photoelectron Spectroscopy (XPS) showed signs of acetylation of the sample. The thermal properties of the solid were also evaluated through Thermogravimetric Analysis (TGA). Scanning Electron Microscopy (SEM) showed cellulose fibers before and after the adsorption process, and some particles with irregular shapes were also observed. The CRS bioadsorbent was used for the effective adsorption of valuable Tb(III) from an aqueous solution. The adsorption data showed a good fit to the Freundlich isotherm and pseudo-second-order kinetic models; however, chemisorption was not ruled out. Finally, desorption experiments revealed the recovery of terbium ions with an efficiency of 97% from the terbium-loaded bioadsorbent.
En el presente trabajo se utiliza la resina de intercambio aniónico para la eliminación de arsénico(III) de medios acuosos. Esta eliminación se ha investigado teniendo en cuenta diversas variables experimentales como son: la velocidad de agitación del sistema, la temperatura, el pH de la disolución y la dosificación de resina al sistema. El equilibrio de intercambio aniónico tiene un carácter endotérmico y no espontaneo, en el rango de temperaturas comprendido entre 20 °C y 60 °C, la cinética del proceso responde al modelo de pseudo-segundo orden, sin embargo, el mecanismo de carga del arsénico en la resina cambia en el rango de temperaturas comprendido entre 20 °C y 40 °C. La isoterma de carga del metal en la resina responde al modelo linearizado de Freundlich. Se comparan los resultados de carga de arsénico en la resina Dowex 1x8 con los obtenidos con otras resinas y con nanotubos de carbono de pared multiple. La elución del arsénico se puede realizar con disoluciones acidas, por ejemplo 1 M HCl.
The behavior of oxidized and non-oxidized multiwalled carbon nanotubes (MWCNTs) in the adsorption of lanthanum(III) from aqueous solutions is described. Metal uptake is studied as a function of several variables such as the stirring speed of the system, pH of the aqueous solution and metal and nanomaterial concentrations. The experimental results are fitted to various kinetic and isotherm models, the rate law being fitted to the film diffusion and particle diffusion models, when the non-oxidized and the oxidized nanomaterials are used to remove lanthanum from the solution, respectively. Sulfuric acid solutions seem to be appropriate to recover the metal from La-loaded nanomaterials.