anusak bilsalam

Dr. anusak bilsalam

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2020 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
PMPongsiri Mungporn
Pongsiri Mungporn
Phatiphat THOUNTHONGPhatiphat THOUNTHONG
Phatiphat THOUNTHONG
Burin YodwongBurin Yodwong
Burin Yodwong
CEChainarin Ekkaravarodome
Chainarin Ekkaravarodome
ABanusak bilsalam
anusak bilsalam
PBPiyabut Burikham
Piyabut Burikham
This paper presents a multi-phase interleaved boost converter supplied by a fuel cell (FC)/reformer power source for highly dynamic transportation applications. A control theory based on the Hamiltonian function approach is considered. Using the port-controlled Hamiltonian system, we propose simple solutions to the dynamic performance and convergence problems when an interaction occurs between the power sources and constant power loads. To corroborate the proposed control law, an FC boost converter (2.5-kW two-phase interleaved converter).

21 December 2023 in IET Power Electronics
Verified
Journal Article
Open access
ABanusak bilsalam
anusak bilsalam
NKNattakorn Ketprapajun
Nattakorn Ketprapajun
PIPuntarika Insri
Puntarika Insri
HSHatta Sawachan
Hatta Sawachan
DGDamien Guilbert
Damien Guilbert
PTPhatiphat Thounthong
Phatiphat Thounthong
This study proposes a non‐isolated DC converter, which is connected in series with an inverter, with a high output voltage conversion ratio for application in electricity generation systems to upgrade low‐voltage to high‐voltage DC. The topology of the proposed converter is based on a boost converter, which has the limitation of a low voltage conversion ratio. The converter is developed and connected using a coupling inductance technique by adding a second winding L 2 coupled with the prototype winding and diode D 2 . This technique increases the voltage ratio via the ratio operator ( N ) of both the induction coils by operating a single switch at a constant frequency of 60 kHz. The working principle of the proposed converter is based on pulse width modulation with a duty cycle ≤40%. When the converter receives a low voltage DC input of 36 V, it converts the input to a high output voltage of 325 V at an output power 125 W, showing a circuit efficiency of 92.48% at full load. The synthesis and design of the controller include a linear approach to represent the parameters using the small signal methodology, which is employed to establish a transfer function. Furthermore, the proposed converter is capable of effectively regulating the output voltage, even when subjected to variations in the output load by employing a proportional–integral control mechanism. The close loop results obtained from simulations and practical implementation verified the proposed circuit design, as both results agreed with the theoretical analysis.

13 May 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
ABanusak bilsalam
anusak bilsalam
CEChainarin Ekkaravarodome
Chainarin Ekkaravarodome
VCViboon Chunkag
Viboon Chunkag
Phatiphat THOUNTHONGPhatiphat THOUNTHONG
Phatiphat THOUNTHONG
This paper presents an analysis on the effect of a parasitic capacitance full-bridge class-D current source rectifier (FB-CDCSR) on a high step-up push–pull multiresonant converter (HSPPMRC). The proposed converter can provide high voltage for a 12 VDC battery using an isolated transformer and an FB-CDCSR. The main switches of the push–pull and diode full-bridge rectifier can be operated under a zero-current switching condition (ZCS). The advantages of this technique are that it uses a leakage inductance to achieve the ZCS for the power switch, and the leakage inductance and parasitic junction capacitance are used to design the secondary side of the resonant circuit. A prototype HSPPMRC was built and operated at 200 kHz fixed switching frequency, 340 VDC output voltage, and 250 W output power. In addition, the efficiency is equal to 96% at maximum load. Analysis of the effect of the parasitic junction capacitance on the full-bridge rectifier indicates that it has a significant impact on the operating point of the resonant tank and voltage. The proposed circuit design was verified via experimental results, which were found to be in agreement with the theoretical analysis.

1 September 2022 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Verified
Journal Article
Open access
PDF file
SSSuriyotai Supanyapong
Suriyotai Supanyapong
WPWachiravit Pattarapongsathi
Wachiravit Pattarapongsathi
ABanusak bilsalam
anusak bilsalam
Damien GuilbertDamien Guilbert
Damien Guilbert
Phatiphat THOUNTHONGPhatiphat THOUNTHONG
Phatiphat THOUNTHONG
In this study, an analysis and modeling circuit for controlling battery charge solar cells based on data management through internet of things (IoT) is presented. For this proposed, a DC-DC forward resonant reset converter is employed and can be charged at a constant current and constant voltage. Data management of various parameters using IoT technology is provided, via which notifications can be sent to an external application. The proposed converter can give an output voltage of 14.4 VDC for a voltage range including between 9 and 18 VDC, using an isolated transformer and a halfwave rectifier circuit. The main switch of the forward resonant reset converter can operate under a zero-turn-on condition. This approach has the benefit of utilizing a leaking inductance. Llkp and resonant capacitor Cr to reset the remaining flux saturation on the high-frequency transformer. A simulation model prototype was created and tested at a set switching frequency of 50 kHz, 14.4 VDC constant output voltage, and output power of approximately 29 W. An efficiency of 96% at maximum full load can be reached. The proposed analysis techniques and mathematical model were verified via simulation and experimental results, and the obtained results are in agreement with the theoretical analysis.

1 September 2022 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Verified
Journal Article
Open access
PDF file
ABanusak bilsalam
anusak bilsalam
Nicu BizonNicu Bizon
Nicu Bizon
Phatiphat THOUNTHONGPhatiphat THOUNTHONG
Phatiphat THOUNTHONG
This study investigates an auxiliary technique for the integration of inductive coil connectors (AIIC) within a single switched DC converter with high voltage gain for renewable energy source applications. The aim is to develop and improve the rate of voltage gain for both coils by using inductive coil connectors (coupling inductance) on the input side that goes through the ratio operator of both inductive coils of the high frequency transformer by having the prototype power circuit operate at a switching frequency 80 kHz. Experimental results show that the output power is at 125 W, output voltage is at 325 V, and input voltage is at 36 V. Furthermore, the duration of change of critical waves of the duty condition was analyzed to confirm that the results were consistent with the proposed technique.

16 January 2025 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
PPP. Prakaivichien
P. Prakaivichien
PPP. Poomsuwan
P. Poomsuwan
KCK. Chaicharoenaudomrung
K. Chaicharoenaudomrung
CEC. Ekkaravarodome
C. Ekkaravarodome
ABanusak bilsalam
anusak bilsalam