To obtain qualified logging while drilling (LWD) data, a new acoustic LWD tool was designed. Its overall design is introduced here, including the physical construction, electronic structure, and operation flowchart. Thereafter, core technologies adopted in this tool are presented, such as dominant exciting wave bands of dipole source, a sine wave pulse excitation circuit, broadband impedance matching, and an intellectualized active reception transducer. Lastly, we tested this tool in the azimuthal anisotropy module well, calibration well, and normal well, working in the model of the cable, sliding eye, and logging while drilling. Experiments showed that the core technologies achieved ideal results and that the LWD tool obtained qualified data.
14 October 2021 in Journal of Petroleum Science and Engineering
Wireless short-hop communication is a crucial solution for information transmission between logging while drilling (LWD) and measurement while drilling (MWD). It is important for closed-loop control in geosteering drilling. Compared with wired transmission, wireless short-hop communication offers a cost-effective and stable alternative. Besides, it reduces drilling risks and improves efficiency. Current research primarily concentrates on magnetic dipole (MD) antennas, where resistivity stands as the only continuous variable under investigation, and discussions regarding other parameters may be constrained. It lacks complex models and fails to account for factors such as borehole mud and antenna slots. This article utilizes the finite element method (FEM) to examine the transmitting and receiving characteristics of electric dipole (ED) and MD antennas. Investigate the effects of transmission conditions and instrument structure on the signal. Experimental validation in a water tank substantiates the reliability and practicality of numerical simulation results. It suggests that using a coil number between 150 and 200 turns with a frequency of 5–8 kHz for both antenna structures in oil-based mud can achieve transmission distances of over 15 m. The antenna slot has minimal impact on the signal. Design considerations should prioritize overall structural stability and mechanical strength. These findings contribute valuable insights to the design and optimization of the instrument.
9 July 2022 in Journal of Geophysics and Engineering
An azimuth electromagnetic propagation logging while drilling tool provides the electrical parameters around a well in the intelligent drilling guidance system. It is a key link in intelligent guidance technology. As the stratum directivity parameter, the azimuth signal is associated with the compensation measurement of the resistivity instrument, which guides the drilling. However, it must be calibrated to have physical significance. The traditional method uses a water tank for calibration. However, this method is affected by the edge effect, which greatly weakens the azimuth signal. The model is complex and difficult to recover, which seriously suppresses the calibration results and causes errors in the azimuth signal. To eliminate the edge effect and simplify the model to improve the signal quality, an instrument calibration method based on sea level as the reflection interface is proposed in this paper. The air–seawater structure can simplify the calculation model, eliminate the edge effect and improve the signal strength. According to 1D air–seawater model simulation and 3D water tank model calculation, the feasibility of the simplified model is analyzed. According to the azimuth signal characteristics of the simplified model, an azimuth signal correction process that is more suitable for azimuth electromagnetic propagation logging while drilling is proposed. The measured data show that the air–seawater model improves the signal-to-noise ratio of the azimuth signal, verifies the detection ability of the azimuth antenna and provides technical support for oil and gas development in complex reservoirs.
Directional resistivity logging-while-drilling tools play an important role in geosteering. In contrast to the widely used tool with magnetic dipole transmitters and receivers, tools are investigated with electric and magnetic dipoles as transmitters and/or receivers for “look-around” boundary detection. Measurement schemes are selected based on their look-around boundary detection abilities. Those measurement schemes are studied regarding the sensitivity and depths of boundary detection, the optimal transmitter-receiver distance and frequency, and the effects of a drill collar using the coefficient propagator method and the finite-difference method. Higher sensitivity to a boundary often implies a shallower depth of investigation. More specifically, the measurement schemes using an electric dipole transmitter and receiver are the least sensitive to the boundary; however, such schemes have the maximum depth of detection and the strongest signal strength. The schemes using electric and magnetic dipole transmitters and receivers have a moderate depth of detection and signal strength. The measurement schemes with a magnetic dipole transmitter and receiver have the highest sensitivity to the boundary and the weakest signal strength. The drill collar affects the response of all of the measurement schemes. However, this effect cannot be corrected with a simple coefficient for the schemes using an axial electric dipole transmitter, but it can be corrected for others. The optimal frequencies and optimal transmitter-receiver distances of those schemes have two types: the changing one that changes with the distance to boundaries and the fixed one that usually has the lowest frequency or the shortest transmitter-receiver distance. The characteristics of each measurement scheme will guide the tool designs and determine its role in the application and method of interpretation.