Cement-emulsified asphalt mixture (CEAM), a kind of cold mix asphalt mixture, has the advantages of energy conservation and emission reduction as well as easy construction. However, the performance of CEAM is not as good as hot mixed asphalt mixtures. Hence, in this study, two different fibers were adopted as the reinforcing phase to improve the comprehensive properties of CEAM. The results indicated that the addition proportion and curing time were crucial to fiber-reinforced cement-emulsified asphalt mixture (FRCEAM). The compressive strengths, water stability, and raveling resistances of FRCEAM preparations with polyester or brucite fibers (FRCEAM-PF and -BF, respectively) were enhanced significantly. FRCEAM-PF had the maximum flexural tensile strength and strain, which meant that its low-temperature performance was the best compared to FRCEAM-PF and CEAM. However, the contribution of PF to CEAM high-temperature stability was greater than that of BF. Fiber addition to CEAM not only enhanced the cycles of fatigue loading but also reduced sensitivity to changes in stress level. Furthermore, FRCEAM-BF durability was slightly better than that of FRCEAM-PF. SEM analysis indicated that fibers provided bridging and meshing effects. Although PF and BF showed different enhancement effects, both mixtures met the requirements for hot mixed asphalt mixtures.
With the acceleration of the construction of sponge cities in China, porous asphalt pavement (PA) is has been widely used. High-viscosity asphalt (HVA) is the core material in building PA because it has good rheology properties, which can provide good raveling and rutting resistance. However, due to the open-graded structure of PA, HVA was more susceptible to rapid aging, which significantly affects the durability of PA. To investigate the thermal aging effect on the rheological properties of self-modified HVA (SHVA), five types of asphalts were aged using a rolling thin film oven (RTFO) and pressure aging vessel (PAV). Then, rheological tests were adopted, such as temperature sweep test (TS), repeated creep and recovery test (RCR), and bending beam rheometer test (BBR). The results indicate that during the aging process, the oxidation-induced hardening effect of neat asphalt and the degradation-induced softening effect of the modifier changes the rheology properties of HVA significantly. As the aging progresses, the contribution of the modifiers of HVA to anti-aging performance is greatly reduced. At high temperatures, HVA demonstrates better anti-aging performance than conventional styrene–butadiene–styrene (SBS)-modified asphalt (Guo Chuang, GC). The change of the high-temperature rheological indices of the two HVA types (SHVA and TAFPACK-super HVA (TPS)) showed a smaller activation energy index (EAI), a more considerable viscous component of binder creep stiffness (Gv), and more minor accumulated stain (racc), indicating a more significant anti-short-term and long-term aging performance, which is beneficial to the high-temperature performance of asphalts. However, the changes in low-temperature rheological properties do not align with those in high-temperature rheological properties after long-term aging. The BBR test results reveal that TPS exhibits worse low-temperature performance than GC and SHVA. During the thermal aging process, the contribution rate of the modifiers in SHVA against RTFO and PAV aging is higher than that of the modifiers in TPS, which contributes to the superior anti-aging property. Overall, SHVA demonstrates the best anti-aging performance among the five asphalts tested.
In order to evaluate and improve the deformation behavior of cement–emulsified asphalt binder (CA) in cement–emulsified asphalt mixture, this study investigated the reinforcement of small additions of fibers (2%, 4%, and 6% addition by mass of cement) on the deformation resistance of CA. A repeated creep recovery test was implemented that measures the recovery rate of creep deformation and accumulated strain. Further, an improved piecewise curve-fitting method was used to determine the parameters of Burgers model, then the creep compliances were fitted and calculated. The results show the repeated creep recovery test to be a suitable method for obtaining useful information about creep and recovery deformation of fiber-reinforced CA. The influence of fiber types and dosages on the deformation recovery ability is determined based on the creep recovery ratio and accumulated strain. The improved piecewise curve-fitting method has high accuracy. Thereafter, the reinforcement effect was analyzed through the evolution of creep compliance under loading. Therefore, this paper can provide a reference for enhancing the properties of cement–emulsified asphalt mixture by maximizing the fiber reinforcement.
In order to evaluate the property of self-modified high viscosity asphalt (SHVA), we use GC SBS modified asphalt (GC)and TPS high viscosity asphalt (TPS) as control group. The rolling thin film oven test (RTFOT) and pressure aging vessel (PAV) were adopted to evaluate the aging property of high viscosity asphalts. And the storage stability of SHVA was measured. The results show that after RTFOT, the ductility, zero shear viscosity, viscosity toughness and toughness of SHVA are better than those of GC and TPS. The Zero shear viscosity of SHVA can still reach 19638Pa·s after PAV. Therefore, the anti-aging performance of SHVA is better than GC and TPS. After heat storage for 72h, the softening point difference of SHVA is 2.3 °C which can meet the storage stability requirement.