Cement-emulsified asphalt mixture (CEAM), a kind of cold mix asphalt mixture, has the advantages of energy conservation and emission reduction as well as easy construction. However, the performance of CEAM is not as good as hot mixed asphalt mixtures. Hence, in this study, two different fibers were adopted as the reinforcing phase to improve the comprehensive properties of CEAM. The results indicated that the addition proportion and curing time were crucial to fiber-reinforced cement-emulsified asphalt mixture (FRCEAM). The compressive strengths, water stability, and raveling resistances of FRCEAM preparations with polyester or brucite fibers (FRCEAM-PF and -BF, respectively) were enhanced significantly. FRCEAM-PF had the maximum flexural tensile strength and strain, which meant that its low-temperature performance was the best compared to FRCEAM-PF and CEAM. However, the contribution of PF to CEAM high-temperature stability was greater than that of BF. Fiber addition to CEAM not only enhanced the cycles of fatigue loading but also reduced sensitivity to changes in stress level. Furthermore, FRCEAM-BF durability was slightly better than that of FRCEAM-PF. SEM analysis indicated that fibers provided bridging and meshing effects. Although PF and BF showed different enhancement effects, both mixtures met the requirements for hot mixed asphalt mixtures.
Bridge safety during operating periods is a primary concern worldwide, and the evaluation of bridge risks is a critical aspect of ensuring bridge safety. The most common methods used for bridge risk evaluations include fuzzy comprehensive evaluations, grey system theory, fault tree analysis, the Kent index method, and data envelopment analysis. However, these approaches are highly subjective and have uneven distributions when determining the weights of risk indicators. To improve the accuracy and feasibility of bridge risk evaluations for a given period of operation, we first establish bridge risk indicators and assign subjective weights to each indicator based on an analytic hierarchy process. Additionally, objective weights are assigned to each indicator according to an entropy weighting method. Then, the combined weights of each risk indicator are obtained by applying game theory principles. This enables the construction of a degree of membership matrix comprising these risk indicators, which is established according to an expert grading method and grey fuzzy theory. Finally, the evaluation results vector is calculated, allowing the risk level of a bridge to be assessed according to the principle of the maximum degree of membership. Overall, this study provides a more accurate and objective method for evaluating bridge risk during a given period of operation.
With the acceleration of the construction of sponge cities in China, porous asphalt pavement (PA) is has been widely used. High-viscosity asphalt (HVA) is the core material in building PA because it has good rheology properties, which can provide good raveling and rutting resistance. However, due to the open-graded structure of PA, HVA was more susceptible to rapid aging, which significantly affects the durability of PA. To investigate the thermal aging effect on the rheological properties of self-modified HVA (SHVA), five types of asphalts were aged using a rolling thin film oven (RTFO) and pressure aging vessel (PAV). Then, rheological tests were adopted, such as temperature sweep test (TS), repeated creep and recovery test (RCR), and bending beam rheometer test (BBR). The results indicate that during the aging process, the oxidation-induced hardening effect of neat asphalt and the degradation-induced softening effect of the modifier changes the rheology properties of HVA significantly. As the aging progresses, the contribution of the modifiers of HVA to anti-aging performance is greatly reduced. At high temperatures, HVA demonstrates better anti-aging performance than conventional styrene–butadiene–styrene (SBS)-modified asphalt (Guo Chuang, GC). The change of the high-temperature rheological indices of the two HVA types (SHVA and TAFPACK-super HVA (TPS)) showed a smaller activation energy index (EAI), a more considerable viscous component of binder creep stiffness (Gv), and more minor accumulated stain (racc), indicating a more significant anti-short-term and long-term aging performance, which is beneficial to the high-temperature performance of asphalts. However, the changes in low-temperature rheological properties do not align with those in high-temperature rheological properties after long-term aging. The BBR test results reveal that TPS exhibits worse low-temperature performance than GC and SHVA. During the thermal aging process, the contribution rate of the modifiers in SHVA against RTFO and PAV aging is higher than that of the modifiers in TPS, which contributes to the superior anti-aging property. Overall, SHVA demonstrates the best anti-aging performance among the five asphalts tested.
Widespread interest has been drawn to the use of solid waste fillers as a partial replacement for natural fillers in high-performance asphalt mixtures in recent years. However, variations in the material properties of solid waste fillers remain a problem for the recycling method. To address this issue, the limestone powder in asphalt mixtures was replaced with three solid waste fillers, including steel slag powder, tailings powder and calcium carbide slag powder in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, a dense-graded asphalt mixture (AC) and a stone matrix asphalt (SMA) mixture were designed, produced and characterized for wet stability. The results show that the asphalt mixtures with solid waste fillers were superior to limestone powder (LP) asphalt mixtures in terms of resistance to water damage, and the steel slag powder showed the best improvement in moisture stability of the asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. With the addition of anti-stripping agents, the moisture stability of the asphalt mixture with limestone filler was also greatly enhanced. On the contrary, a marginal enhancement was observed in the moisture stability of asphalt mixtures using solid waste fillers. Solid waste fillers can be used in asphalt mixtures and have a similar function as that of anti-stripping agents. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added recycling option.