We present a novel, low-cost approach to fabricate flexible piezoelectric nanogenerators (NGs) consisting of ZnO nanowires (NWs) on carbon fibers and foldable Au-coated ZnO NWs on paper. By using such designed structure of the NGs, the radial ZnO NWs on a cylindrical fiber can be utilized fully and the electrical output of the NG is improved. The electrical output behavior of the NGs can be optionally controlled by increasing the fiber number, adjusting the strain rate and connection modes. For the single-fiber based NGs, the output voltage is 17 mV and the current density is about 0.09 μA·cm⁻², and the electrical output is enhanced greatly compared to that of previous similar micro-fiber based NGs. Compared with the single-fiber based NGs, the output current of the multi-fiber based NGs made of 200 carbon fibers increased 100-fold. An output voltage of 18 mV and current of 35 nA are generated from the multi-fiber based NGs. The electrical energy generated by the NGs is enough to power a practical device. The developed novel NGs can be used for smart textile structures, wearable and self-powered nanodevices.

We report the flexible piezotronic strain sensors fabricated using carbon fiber–ZnO nanowire hybrid structures by a novel and reliable method. The I–V characteristic of the sensor shows high sensitivity to external strain due to the change in Schottky barrier height (SBH), which has a linear relationship with strain. This fabricated strain sensor has a quick, real-time current response under both static and dynamic mechanical loads. The change in SBH resulted from the strain-induced piezoelectric potential is investigated by band gap theory. In this work we develop a new feasible method to fabricate a flexible strain sensor within the fabric adapted to textile structures, able to measure their strain.

Young's modulus, fracture stress, and Poisson's ratio are important mechanical characteristics for micromechanical devices. The Poisson's ratio of a material is a good measure to elucidate its mechanical behavior and generally is the negative ratio of transverse to axial strain. A nanocrystalline (NCD) and an ultrananocrystalline (UNCD) diamond sample with grain boundaries of different chemical and structural constitutions have been investigated by an ultrasonic resonance method. For both samples, the elastic moduli are considerably reduced, compared with the elastic modulus of single crystal diamond (sc-diamond). Depending on the chemical and structural constitution of grain boundaries in nano- and ultrananocrystalline diamond different values for Poisson's ratio and for the fracture strength are observed. We found a Poisson's ratio of 0.201 ± 0.041 for the ultrananocrystalline sample and 0.034 ± 0.017 for the nanocrystalline sample. We discuss these results on the basis of a model for granular media. Higher disorder in the grain boundary leads to lower shear stiffness between the single grains and ultimately results in a decrease of Young's and shear modulus and possibly of the fracture strength of the material.

The titanium alloy Ti–6Al–4V (Ti64) is a very widely applied alloy with extreme importance in the fields of aerospace, automotive, and biomedicine. For a large range of manufacturing methods that involve the liquid phase, such as casting, metal injection molding, thermal spraying, and additive manufacturing, process simulations are an important tool for the optimization and development of the fabrication process. Reliable thermophysical property data of Ti64 in the solid and the liquid phase are necessary inputs to such models. Due to the high melt reactivity of titanium alloys with container materials, measurements performed using conventional thermophysical equipment are usually impossible. Precise benchmark measurement of thermophysical properties (surface tension, viscosity, specific heat, total hemispherical emissivity, thermal conductivity, electrical resistivity, mass density) of Ti64 is presented in the undercooled liquid phase using containerless electromagnetic levitation on board the International Space Station (ISS). The obtained values are compared with predictive models that can help to analyze the data for other compositions of the alloy system. The property values are applied to simulations of industrial fabrication processes, to optimize these processes and thus the product quality.

In this work, we show that ultra nanocrystalline diamond (UNCD) surfaces have been modified to add them hydrophobic and hydrophilic properties. The nanocrystalline diamond films were deposited using the hot filament chemical vapor deposition (HFCVD) technique. This allows growing diamond on different substrates which can be even 3D or structured. Silicon and, for optical applications, transparent quartz glass are the preferred substrates for UNCD layers growth. Fluorine termination leads to strong hydrophobic properties as indicated by a high contact angle for water of more than 100°. Hydrogen termination shows lesser hydrophobic behavior. Hydrophilic characteristics has been realised with oxygen termination. X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDX) measurements confirm the oxygen and fluorine- termination on the nanocrystalline diamond surface. Further, by micropatterning using photolithography, multi-terminated layers have been created with both hydrophobic and hydrophilic areas. In addition, we have shown that retermination is achieved, and the properties of the surface have been changed from hydrophobic to hydrophilic and vice versa. Micro- roughness and stress in the grown film influences slightly the wetting angle as well. The opportunity to realize local differences in hydrophobicity on nanocrystalline diamond layers, in any size or geometry, offers interesting applications for example in microbiological investigations. Multi-terminated arrays show identical surface roughness and at the same time differences in hydrophobicity. These arrays have been visualized with scanning electron microscopy (SEM) and lateral force microscopy (LFM)