Jing Yang

Dr. Jing Yang


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
SBShaoxian Bai
Shaoxian Bai
JHJialin Hao
Jialin Hao
JYJing Yang
Jing Yang
YSYuansen Song
Yuansen Song
For gas–liquid medium isolation seals in aero-engines, the upstream pumping function of directional grooves provides an effective way to realize the design of longer service life and lower leakage rate. However, this produces a new problem for gas–liquid mass transfer in the sealing clearance. This study establishes an analytical model to investigate the gas–liquid mass transfer behavior and the change rule for the opening force of mechanical face seals with elliptical grooves. Compared with traditional studies, this model considers not only the gas–liquid transfer but also the cavitation effect. The results obtained show that with the increase of rotational speed, the gas medium transferred from the inner low-pressure side to the outer high-pressure side. In addition, the leakage rate of the liquid medium from the outer high-pressure side to the inner low-pressure side increased with the growth of sealing clearance, rotational speed and seal pressure. The upstream pumping effect of the gas medium with elliptical grooves not only led to a state of gas–liquid mixed lubrication in the sealing surfaces, but also significantly increased the opening capacity of the seal face. This research may provide a reasonable basis for the design of upstream pumping mechanical face seals.

12 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
SBShaoxian Bai
Shaoxian Bai
CCChudongdomng Chu
Chudongdomng Chu
CMChunhong Ma
Chunhong Ma
JYJing Yang
Jing Yang
SBShiyi Bao
Shiyi Bao
The force equilibrium and moment equilibrium play a significant role on the sealing performance of gas split floating ring seals. A small deflection angle may generate seriously wear on sealing surface and cause seal failure. Therefore, the thermo-hydrodynamic lubrication analysis of gas split floating ring seal with Rayleigh grooves is investigated considering the deflection angle and frictional heat of surface contact, which is beneficial to grasp the hydrodynamic characteristics and rules under high-temperature and high-speed conditions. Pressure and temperature distributions of sealing rings are numerically calculated for the cases with different deflection angle, rational speed, seal pressure and ambient temperature. Then, the hydrodynamic effect and sealing performance are analyzed. The obtained results show that, the surface Rayleigh step grooves do not present obvious hydrodynamic effect when split seal ring has no deflection. While, a significant hydrodynamic effect can be obtained when the split seal ring presents a deflection angle about dozens of micro radians. Here, a 10% increase of opening force is achieved when the deflection angle reaches 80 μrad in the case of speed 30,000 r/min and seal pressure 0.2 MPa. Moreover, the hydrodynamic effect becomes obvious with increasing deflection angle as well as rotational speed. Meanwhile, the growth of rotational speed results in an obvious increase of film temperature. The increase of ambient temperature has a significant influence on the decrease of leakage rate. When the ambient temperature increases from 340 K to 540 K, the leakage rate reduces exceeding 50%, however, it does not present obvious effect on the opening force. The proposed model has the potential to provide the theoretical basis and design guidance for surface grooves of gas split floating ring seal in the future.

27 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
DZDelei Zhu
Delei Zhu
JYJing Yang
Jing Yang
SBShaoxian Bai
Shaoxian Bai
Thermoelastohydrodynamic lubrication behaviors of helium gas T-groove face seals are numerically simulated under conditions of low temperature and high pressure, with the consideration of real-gas properties including compressibility coefficient, viscosity, and heat capacity. It is found that helium gas T-groove face seal presents a sharp divergent deformation at low temperature and high pressure, which makes the opening performance weaken and the leakage rate increase. This result is obviously different from the case of high-temperature gas face seals. As the sealing temperature drops from 300 K to 150 K, the leakage rate increases about 17% and the opening force decreases about 15%. Moreover, with the growth of rotational speed, both the outlet film pressure and the sealing performance present a non-monotonic trend. Specifically, while the rotating speed of moving ring raises from 3000 to 30,000 r·min−1, the leakage rate changes more than 30%, and the opening force is reduced about 10%.

21 March 2024 in Materials
Verified
Journal Article
Open access
PDF file
JCJunjie Chen
Junjie Chen
CMChunhong Ma
Chunhong Ma
SBShaoxian Bai
Shaoxian Bai
JYJing Yang
Jing Yang
The property of vaporization phase transition in liquid oxygen face seals is a key factor affecting the stability of mechanical face seals in many fields, especially under cryogenic conditions. Here, a numerical model based on the saturated vapor pressure is established to investigate the vaporization phase transition property of liquid oxygen sealing film. The novelty of this model is to take the influence of heat transfer and face distortions into consideration at the same time. The pressure and temperature distributions as well as face distortions are calculated, and then the property of vaporization phase transition and sealing performance are analyzed. It is found that spiral grooves may lead to the complex film temperature distributions and irregular vaporization distributions. With the increase in seal temperature and decrease in seal pressure, the vaporization area extends from the low-pressure side to the grooves area, and the vaporization rate increases rapidly. The more important thing is that the vaporization often brings a drastic fluctuation and non-monotonic change in opening force. Specifically, with the increase inin seal temperature from 55 K to 140 K, the opening force fluctuates violently, and the fluctuation range is more than 50%, showing an obvious instability. Finally, this study provides a design range of pressure and temperature values for liquid oxygen face seals. In these ranges, this kind of face seals can have a stable operation, which is beneficial to the practice engineering related to the complex properties of sealing fluid.

20 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
SBShaoxian Bai
Shaoxian Bai
KLKaixin Li
Kaixin Li
JYJing Yang
Jing Yang
SBShiyi Bao
Shiyi Bao
CMChunhong Ma
Chunhong Ma
In order to obtain the leakage characteristics of an upstream pumping face seal with inclined ellipse dimples under high-temperature and high-speed liquid lubricating conditions, a thermo-hydrodynamic lubricating model is developed. The novelty of this model is that it takes the thermo-viscosity effect and cavitation effect into account. The influence of operating parameters, such as rotational speed, seal clearance, seal pressure, ambient temperature and structural parameters, such as dimple depth, inclination angle, slender ratio and dimple number on the opening force and leakage rate, is numerically calculated. The results obtained show that the thermo-viscosity effect makes the cavitation intensity decrease noticeably, leading to an increase in the upstream pumping effect of ellipse dimples. Moreover, the thermo-viscosity effect may make both the upstream pumping leakage rate and opening force increase by about 10%. It can also be found that the inclined ellipse dimples can produce an obvious upstream pumping effect and hydrodynamic effect. Based on the reasonable design of the dimple parameter, not only can the sealed medium achieve zero leakage, but the opening force can also increase by more than 50%. The proposed model has the potential to provide the theoretical basis for and guide the future designs of upstreaming liquid face seals.

18 June 2025 in Materials
Verified
Journal Article
Open access
PDF file
SBShaoxian Bai
Shaoxian Bai
LQLIU JIA QI
LIU JIA QI
JYJing Yang
Jing Yang
The upstream pumping effect of mechanical face seals has a significant influence on their sealing performance. In order to reveal the effect of deep grooves on upstream pumping effects, an experimental and theoretical analysis is carried out in this study. The main novelty of this paper is to analyze the feasibility of deep grooves in a mechanical seal design from the perspective of cavitation and leakage rate. Firstly, an upstream pumping spiral groove is designed and fabricated, with different groove depths from 2 μm to 90 μm. Then, testing is performed with water as the sealing medium. Finally, the cavitation phenomena are captured, and leakage rates are measured during the experiment. The obtained results show that the groove with a depth of tens of microns can be designed according to the laminar flow hypothesis, and Reynolds equation is still valid to predict the cavitation and leakage rate theoretically. The spiral groove with a depth of tens of microns shows a significant upstream pumping effect. Both the theoretical and experimental analyses show that under certain working conditions, deep grooves can realize the zero-leakage sealing design of liquid, which might provide significant guidance for the sealing design of mechanical face seals to enhance sealing performance.