We compare four approaches to geomechanical modeling of stresses adjacent to salt bodies. These approaches are distinguished by their use of elastic or elastoplastic constitutive laws for sediments surrounding the salt, as well as their treatment of fluid pressures in modeling. We simulate total stress in an elastic medium and then subtract an assumed pore pressure after calculations are complete; simulate effective stress in an elastic medium and use assumed pore pressure during calculations; simulate total stress in an elastoplastic medium, either ignoring pore pressure or approximating its effects by decreasing the internal friction angle; and simulate effective stress in an elastoplastic medium and use assumed pore pressure during calculations. To evaluate these approaches, we compare stresses generated by viscoelastic stress relaxation of a salt sphere. In all cases, relaxation causes the salt sphere to shorten vertically and expand laterally, producing extensional strains above and below the sphere and shortening against the sphere flanks. Deviatoric stresses are highest when sediments are assumed to be elastic, whereas plastic yielding in elastoplastic models places an upper limit on deviatoric stresses that the rocks can support, so stress perturbations are smaller. These comparisons provide insights into stresses around salt bodies and give geoscientists a basis for evaluating and comparing stress predictions.
6 December 2018 in Journal of Geophysical Research: Solid Earth
Intensive studies following the 2008 Wenchuan and 2013 Lushan earthquakes have shown that these two events have changed stresses on major faults in eastern Tibetan Plateau. However, these stress changes are small perturbations to total stresses on these faults. To evaluate full stress evolution on faults and the associated earthquake hazard, we need to consider the effects of all regional large earthquakes and tectonic stressing on faults. Here we use a three‐dimensional viscoelastoplastic finite element model to investigate stress evolution and long‐term temporal patterns of seismicity on major faults in eastern Tibet. We first simulate stress changes due to coseismic slips and postseismic viscoelastic stress relaxation by regional 28 big earthquakes since 1327 and find that nine events, including the Wenchuan earthquake, occurred where Coulomb stress was decreased by the preceding events. We then evaluate interseismic stressing rates using the geodynamic model and GPS data and find the highest rate on Xianshuihe fault (~1,000–4,950 Pa/yr) and the lowest rate on Longmenshan fault (~150–1,133 Pa/yr). Including interseismic stressing in stress evolution shows that the Wenchuan earthquake ruptured where Coulomb stress had increased since 1327 and stresses on southern Xianshuihe and central Anninghe faults would have reached prerupture stress levels of their preceding ruptures. Finally, we analyze synthetic seismicity on faults and find that earthquakes on each fault tend to occur in clusters, separated by quiescent periods whose lengths are inversely related with fault slip rates. The time spans of earthquake clusters are affected by fault slip rates, fault configuration, and rheology.
18 July 2017 in Journal of Geophysical Research: Solid Earth
The 17 June 2018 6.1 ( 5.5) Osaka earthquake exhibits a large non–double‐couple component (), and its aftershock sequence shows a complicated spatial pattern. To better understand the ruptured faults, we relocate the earthquake sequence using P and S arrival times and waveform cross correlations and calculate the focal mechanisms of all () earthquakes within three months after the mainshock using P‐wave first‐motion polarities and S/P amplitude ratios. Relocated aftershocks image several faults, the northeast‐striking strike‐slip fault, the north‐northwest‐striking reverse fault, and at least two small northwest‐striking features. P‐wave first motions of the mainshock indicate nearly a pure thrust mechanism. We deduce that the earthquake sequence started from a north‐northwest‐striking reverse fault and propagated to a northeast‐striking strike‐slip fault. The aligned strike‐slip aftershocks occurring in the vicinity of the northeast‐striking strike‐slip fault delineates the growth of several newly formed or reactivated northwest‐striking Riedel shears that are conjugated to the northeast‐striking strike‐slip fault.
25 May 2022 in Earth and Planetary Science Letters
The seismic b-value in Gutenberg–Richter law is an important parameter in earthquake science research and earthquake risk assessment. People have tried to use b-values for short-term earthquake forecasts, and this requires the premise of estimating reliable b-values for real-time seismic catalogs. However, estimating b-values for real-time catalogs, which are usually of poor qualities, is usually faced with many difficulties and problems. In this study, through a series of numerical tests, we investigate the performance of three methods, including the commonly used maximum likelihood estimation method and two relatively new b-value estimation methods, namely the b-positive and K − M slope methods, on calculating b-values for real-time seismic catalogs. We also apply these three methods to both observed seismic catalogs (the seismic sequence in the Costa Marchigiana, Italy, and a high-resolution early aftershock sequence of the 2023 two Mw ∼7.8 earthquakes in Türkiye) and synthetic real-time seismic catalogs. The results in this study show that it seems difficult to obtain accurate b-values for real-time earthquake catalogs by each of these three methods, but the combination of these methods may give a better judgment—if all three methods suggest that the change in b-value is significant, the probability of making a correct decision is very high. Facing the uncertainty of b-value estimation that always exists, we advocate exploring the effectiveness of standard b-value estimation strategies in practical applications.