Oxidative conversion of methane to acetic acid at 150°С and a pressure of 6.5 MPa with the assistance of carbon monoxide on rhodium-modified ZSM-5 zeolites with different SiO2/Al2O3 molar ratios was studied. A decrease in SiO2/Al2O3 from 300 to 30 leads to a 2.7-fold increase in the acetic acid yield. Such behavior of the catalytic system correlates with an increase in the acidity, primarily with an increase in the density of Brønsted acid sites on the zeolite surface. Introduction of 0.1–0.5 wt % rhodium into the zeolite increases the acetic acid yield by a factor of more than 3. The highest acetic acid yield (0.53 mmol/gcat) is attained on the zeolite with SiO2/Al2O3 = 33 modified with 0.5 wt % Rh. The methane transformation to acetic acid occurs while involving both the acid sites of the zeolite and the sites formed by reactive rhodium particles.
21 September 2022 in Microporous and Mesoporous Materials
The effect of steam on the catalytic properties of La-Zr-HZSM-5/Al2O3 and Mg-HZSM-5/Al2O3 in the synthesis of olefins from dimethyl ether (DME) has been studied. It has been found that the presence of steam has a significant effect on the ethylene-to-propylene ratio regardless of the nature of the modifier; the formation of methanol was observed only on Mg-HZSM-5/Al2O3. In situ high-temperature diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy has revealed that the formation of methanol on Mg-HZSM-5/Al2O3 occurs owing to the formation of methoxy groups on the surface of the zeolite during the interaction between DME and basic sites. The resulting methoxy groups can be easily converted to methanol in the presence of steam.
Isolated and associated OH groups have been in situ identified by high-temperature diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy of the surface of zeolites calcined until complete removal of water. It has been shown that the Brønsted acid sites (BASs) involved in dimethyl ether (DME) conversion on the zeolite surface exhibit two characteristic bands in the DRIFT spectra. It has been found that the composition of DME conversion products on HZSM-5 zeolite catalysts modified with Mg or Rh is temperature-dependent. Ethanol and a small amount of methanol were detected on an Rh-HZSM-5/Al2O3 zeolite catalyst at T = 270°C and were not observed on Mg-HZSM-5/Al2O3 under the same conditions. Spectral features of ketene were detected in the DRIFT spectra of the surface of Mg-HZSM-5/Al2O3 in a stream of DME. The spectrum of Rh-HZSM-5/Al2O3 calcined at 200°C exhibited spectral features of ethyl alcohol and bands characterizing a strong Lewis acid site (LAS) capable of hydrogenating ketene to ethyl alcohol. The spectra of the surface of all the zeolite catalysts tested in a DME stream at 320°C contain bands characterizing olefins and alkanes and do not exhibit the spectral features of alcohols and ketene.
The stability of the zeolite component and a La-Zr-HZSM-5/Al2O3 catalyst synthesized on its basis in the synthesis of lower olefins from dimethyl ether (DME) has been studied. It has been shown that both the zeolite component and the catalyst based on it exhibit highly stable catalytic properties. A high-temperature treatment of the zeolite component and the finished La-Zr-HZSM-5/Al2O3 catalyst with air and steam, respectively, leads to a significant increase in the catalyst selectivity for olefins, particularly propylene, while the activity in the DME conversion slightly decreases as the steaming temperature increases from 500 to 750°C.
1 January 2022 in Microporous and Mesoporous Materials