Teemu Ojala

Mr. Teemu Ojala

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
TOTeemu Ojala
Teemu Ojala
YCYanjuan Chen
Yanjuan Chen
JPJouni Punkki
Jouni Punkki
FAFahim Al-Neshawy
Fahim Al-Neshawy
This paper presents the characteristics of air void systems in hardened concrete with the method of digital image analysis (DIA) coupled with Schwartz-Saltykov (SS) conversion. The results indicate that the DIA method coupled with SS conversion estimates the air content with more accuracy than it would without SS conversion; the correlation between air content obtained from the DIA method, and that from the thin section (TS) method is as good as the correlation observed between the pressure saturation (PS) method and the TS method. It was also found that the DIA method shows a better correlation with the TS method when the spacing factor without SS conversion is considered, while both methods show poor correlations when the corresponding specific surface is considered. In addition, it indicates that the peak of three-dimensional size distribution (3-DSD) of air voids after SS conversion falls in smaller voids, and 3-DSD of air voids shifts to a narrow size range, in comparison with the 2-DSD without SS conversion; the shape of the 3-DSD air voids remains constant irrespective of the class widths. Increasing the number of classes can minimise the standard deviation in the estimation, however, it also results in a leap in voids volume density, which will influence the estimation of air content.

21 April 2023 in Construction and Building Materials
Verified
Journal Article
Open access
TOTeemu Ojala
Teemu Ojala
HAHassan Ahmed
Hassan Ahmed
PKPetri Kuusela
Petri Kuusela
ASAku Seppänen
Aku Seppänen
JPJouni Punkki
Jouni Punkki

10 July 2024 in Sensors
Verified
Journal Article
Open access
PDF file
TOTeemu Ojala
Teemu Ojala
JPJouni Punkki
Jouni Punkki
The correct workability of concrete is an essential parameter for its placement and compaction. However, an absence of automatic and transparent measurement methods to estimate the workability of concrete hinders the adaptation from laborious traditional methods such as the slump test. In this paper, we developed a machine-learning framework for estimating the slump class of concrete in the mixer using a stereovision camera. Depth data from five different slump classes was transformed into Haralick texture features to train several machine-learning classifiers. The best-performing classifier achieved a multiclass classification accuracy of 0.8179 with the XGBoost algorithm. Furthermore, we found through statistical analysis that while the denoising of depth data has little effect on the accuracy, the feature extraction of mixer blades and the choice of region of interest significantly increase the accuracy and the efficiency of the classifiers. The proposed framework shows robust results, indicating that stereovision is a competitive solution to estimate the workability of concrete during concrete production.

1 December 2024 in Nordic Concrete Research
Verified
Journal Article
Open access
PDF file
AIAhsan Iqbal
Ahsan Iqbal
TOTeemu Ojala
Teemu Ojala
FAFahim Al-Neshawy
Fahim Al-Neshawy
JPJouni Punkki
Jouni Punkki
The construction industry is pursuing the reduction of CO2 emissions and the development of lowcarbon concrete. LOIKKA research project was initiated in Finland with the aim to reduce the CO2 emissions of concrete manufacturing by 50%. The use of blast furnace slag was seen as the most competitive way to significantly reduce CO2 emissions of concrete. However, incorporating slag in concrete can lead to durability complications, particularly concerning salt freeze-thaw resistance. This study investigates the effects of slag content, carbonation/ageing, and pre-curing conditions on the freeze-thaw and salt freeze-thaw resistance of concrete. Additionally, it evaluates the compressive strength development and porosity differences of test concretes. Slab tests were conducted to determine the surface scaling and internal damage resistance of concrete specimens. The results showed that high slag content and carbonation reduced salt freeze-thaw resistance. The incorporation of 50% slag content as the cement clinker replacement is considered critical. An increase in slag content led to a decrease in the compressive strength at 7 days due to the low reactivity of slag but achieved the highest compressive strength at 91 days with 70% slag content. These insights contribute to our understanding of the durability properties of concrete incorporating slag.

1 December 2024 in Nordic Concrete Research
Verified
Journal Article
Open access
PDF file
TOTeemu Ojala
Teemu Ojala
JPJouni Punkki
Jouni Punkki
Current testing methods for fresh concrete are time-consuming and operator-dependent and, thus, should be replaced with automatic testing methods. This study investigated automated measurement techniques for determining water/cement (w/c) ratio and air content in fresh concrete, addressing this need for more efficient and continuous quality control. The research compared microwave absorption (MWA) and time-domain reflectometry (TDR) techniques for w/c ratio measurement as well as acoustic wave propagation (AWP) technique for air content measurement, against the reference testing methods. Laboratory investigations were conducted on various concrete mix compositions. Results showed that MWA and TDR techniques demonstrated a good correlation with reference methods for w/c ratio (R² = 0.808 and 0.858, respectively), but were sensitive to air content variations. The AWP technique for air content measurement showed a moderate correlation with the pressure method (R² = 0.654 for static measurements), with accuracy influenced by concrete consistency. The study highlights the potential of these automated techniques for real-time concrete quality control, while also revealing limitations related to mix composition variations and calibration requirements. These findings contribute to the ongoing development of more precise and reliable automated measurement systems for fresh concrete properties, supporting the move towards advanced quality control methods.