The extensive application of antibiotics in human and veterinary medicine has led to their widespread occurrence in a natural aquatic environment. Global health crisis is associated with the fast development of antimicrobial resistance, as more and more infectious diseases cannot be treated more than once. Sulfamethoxazole, trimethoprim and ciprofloxacin are the most commonly detected antibiotics in water systems worldwide. The persistent and toxic nature of these antibiotics makes their elimination by conventional treatment methods at wastewater treatment plants almost impossible. The application of advanced oxidation processes and heterogeneous photocatalysis over TiO2-based materials is a promising solution. This highly efficient technology has the potential to be sustainable, cost-efficient and energy-efficient. A comprehensive review on the application of various TiO2-based photocatalysts for the degradation of sulfamethoxazole, trimethoprim and ciprofloxacin is focused on highlighting their photocatalytic performance under various reaction conditions (different amounts of pollutant and photocatalyst, pH, light source, reaction media, presence of inorganic ions, natural organic matter, oxidants). Mineralization efficiency and ecotoxicity of final products have been also considered. Further research needs have been presented based on the literature findings. Among them, design and development of highly efficient under sunlight, stable, recyclable and cost-effective TiO2-based materials; usage of real wastewaters for photocatalytic tests; and compulsory assessment of products ecotoxicity are the most important research tasks in order to meet requirements for industrial application.
7 February 2020 in Journal of Inorganic and Organometallic Polymers and Materials
This article is devoted to TiO2/ZnO nanocomposites creation by modifying with the commercial TiO2/P90 product using the impregnation method and identifying the effect of the ZnO modifier on its adsorption, structural, photocatalytic, and electrical properties. The synthesized TiO2/ZnO nanocomposites were characterized by XRD, XRF, XPS, and low-temperature nitrogen adsorption-desorption methods. As a result, nanostructured TiO2/ZnO composites with the ZnO content of 2, 5, 10, and 15 were obtained. It was shown that the phase composition of TiO2/P90 does not change during the nanocomposite synthesis. XPS studies of TiO2/ZnO nanocomposites indicated the presence of Ti4+, Zn2+, O2−, and OH states on their surface, which is associated with TiO2, ZnO, and hydroxide ions. The nitrogen adsorption-desorption method showed that the commercial TiO2/P90 sample is nonporous, and all TiO2/ZnO nanocomposites are characterized by almost the same homogeneous mesoporous structure. Experimentally established sorption and photocatalytic properties depend on the specific surface area and electrostatic interaction with dyes. The effect of the ZnO modifier on I-V characteristics of the TiO2/P90 sample was revealed. The obtained experimental data showed that the TiO2/P90 sample contains one type of current carriers, and TiO2/2ZnO and TiO2/5ZnO nanocomposites are characterized by two types of current carriers.
TiO2 nanoparticles were synthesized by sol–gel and hydrothermal methods from Titanium (IV) isopropoxide. The obtained materials were studied for photocatalytic removal of antibiotic ciprofloxacin under UVA light. The samples were characterized using x-ray diffraction, transmission electron microscopy, scanning electron microscopy and N2-physisorption. The most active samples were obtained at pH 1.0 via sol–gel synthesis (SG TiO2 pH 1.0); and using 2-propanol at 110 °C via hydrothermal method (HT TiO2 Pr 110). The SG TiO2 pH 1.0 sample demonstrated higher crystallinity but lower specific surface area (23 m2/g) compared to the HT TiO2 Pr 110 sample (315 m2/g). Both samples demonstrated good photoactivity after 120 min, removing ciprofloxacin up to 99%. However, adsorption accounted for most antibiotic removal by the HT TiO2 Pr 110 sample, while photocatalysis played predominant role in the case of the SG TiO2 pH 1.0 sample.