Ge Jinming

Dr. Ge Jinming

Harbin Institute of Technology
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2023 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
ZWZhenhao Wang
Zhenhao Wang
FMFanyu Meng
Fanyu Meng
YZYue Zhang
Yue Zhang
WWWei Wang
Wei Wang
GLGuoqing Li
Guoqing Li
GJGe Jinming
Ge Jinming
Presently, conventional fixed parameters are applied in dual-parallel virtual synchronous generators (VSGs), resulting in poor frequency response characteristics. Therefore, a multi-parameter cooperative adaptive control strategy is proposed in this paper as a solution. The principle of the method is that when a frequency transient fluctuation occurs in the VSG, the frequency deviation and rate of frequency change are combined with the virtual inertia, damping coefficient, and P /ω droop coefficient to form an adaptive control system. A small-signal model of dual-parallel VSGs was built to analyse the impacts of the parameters on the stability of the system in each phase. The boundary conditions of the parameters such as virtual inertia, damping coefficient, P/ω droop coefficient and virtual inertia adjustment coefficient are further pinpointed to improve parameters' values. In the simulation results, the strategy put forward in this paper can increase the frequency and amplitude by 54.66% and the recovery time by 49.65% when the system is disturbed. The simulation and the StarSim experimental platform are verified that the strategy proposed in this paper can effectively optimize the frequency fluctuation response characteristics of the grid-connected VSG system in different cases, enhancing the dynamic performance and safety and stability of the system.

22 November 2019 in Sensors
Verified
Journal Article
Open access
PDF file
GJGe Jinming
Ge Jinming
SYShen Yan
Shen Yan
WYWenbin Yu
Wenbin Yu
YHYue Han
Yue Han
FDFang-Wei Duan
Fang-Wei Duan
Accurate and reliable lightning current data are the basis of lightning protection design. To measure lightning current data at different measurement locations in a transmission system, the limitations of traditional lightning current sensors are analyzed, and optical current sensing technology is adopted, which has the advantages of no magnetic saturation and no bandwidth limitation. Compared with traditional application environments, the sensing technology is used in special environments in transmission systems. This paper analyzes the influence of environmental factors on sensors, and combines the extreme environmental requirements, such as temperature and insulation requirements, to study the sensor. Starting from the sensitivity, the sensing characteristics of the sensor are analyzed. The sensor is designed according to three aspects: sensing material selection, spatial measuring position, and sensing material size optimization, such that it can satisfy the different measurement requirements of towers, overhead ground wires, and transmission lines, respectively. The experiments indicate that the developed sensors can meet the measurement sensitivity requirements of different types of lightning strikes. The experimental results of sensors exhibit a reasonable amplitude measurement accuracy, linearity, and waveform measurement capability. These results provide important theoretical and experimental bases for the application of optical current sensing technology to the measurement of the lightning current of transmission systems.

6 November 2018 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
PDF file
SYShen Yan
Shen Yan
GJGe Jinming
Ge Jinming
RLRui‐Tong Liu
Rui‐Tong Liu
WFWei Fan
Wei Fan
YYYing‐Xuan Yang
Ying‐Xuan Yang

30 June 2018 in Optik
Verified
Journal Article
Closed access
SYShen Yan
Shen Yan
GJGe Jinming
Ge Jinming
RLRui-Tong Liu
Rui-Tong Liu
WFWei Fan
Wei Fan
YYYing-Xuan Yang
Ying-Xuan Yang

7 July 2019 in Sensors
Verified
Journal Article
Open access
PDF file
SYShen Yan
Shen Yan
TCTong Chen
Tong Chen
WYWenbin Yu
Wenbin Yu
GJGe Jinming
Ge Jinming
YHYue Han
Yue Han
FDFang-Wei Duan
Fang-Wei Duan
When applying an optical current transformer (OCT) to direct current measurement, output signals exhibit a low signal-to-noise ratio and signal-to-noise band overlap. Sinusoidal wave modulation is used to solve this problem. A double correlation detection algorithm is used to extract the direct current (DC) signal, remove white noise and improve the signal-to-noise ratio. Our sensing unit uses a terbium gallium garnet crystal in order to increase the output signal-to-noise ratio and measurement sensitivity. Measurement errors of single correlation and double correlation detection algorithms are compared, and experimental results showed that this measurement method can control measurement error to about 0.3%, thus verifying its feasibility.

26 September 2018 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
SYShen Yan
Shen Yan
GJGe Jinming
Ge Jinming