Phase-shift or pole-shift method can reduce the detent force of the double-sided permanent magnet linear synchronous motor (DS-PMLSM) dramatically. However, this method causes a decrease in thrust and an increase in normal force simultaneously. To overcome this drawback, a novel slot-shift structure whose slots on the two sides of the primary component are staggered by an optimal distance is proposed in this paper. The models of the detent force including the end force and cogging force is established theoretically, and then verified by finite element (FEM) analysis. The windings in the upper primary and the lower primary are arranged differently to improve the average thrust. The thrust characteristics of the DS-PMLSM under different shifted distances are analyzed and compared in detail. Furthermore, the primary component employing two kinds of core laminations is proposed to reduce both the dc component and ripple of the normal force. Finally, a DS-PMLSM prototype is tested, and the experimental results are compared with the analytical results to verify the effectiveness of the theoretical and simulation research.
17 January 2019 in IEEE Transactions on Industrial Electronics
The longitudinal end effect of the double-sided permanent magnet linear synchronous motor (DS-PMLSM) causes a large end force. To overcome this drawback, this paper proposes a novel DS-PMLSM structure, in which the upper or lower primary component is shifted by a certain distance. First, the end-force model of the DS-PMLSM is established, based on which, the influences of the staggered structure on the fundamental and higher-order end-force components are analysed. Following this, the DS-PMLSMs with different slot-pole combinations are divided into four categories, and the design principles of possible winding arrangements are discussed. Furthermore, the staggered structures are applied to four slot-pole combinations, namely 21-pole/18-slot, 15-pole/18-slot, 20-pole/18-slot, and 16-pole/18-slot. The back electromotive forces (EMFs), detent forces, thrusts and normal forces of the four combinations are analysed and compared through the finite element method (FEM). The electromagnetic and output characteristics of the novel DS-PMLSM are also compared with the traditional DS-PMLSM prototype to verify the effect of the proposed structure on suppressing the end force.
1 August 2018 in IEEE Transactions on Industrial Electronics
Traditionally, straggering the primaries of the double-sided permanent magnet linear synchronous motor (DS-PMLSM) is beneficial in helping to reduce the detent force caused by the longitudinal end effect, but leading to a reduction of the average thrust. To overcome this disadvantage, this paper provides a novel DS-PMLSM, which adopts the structure of staggering two primaries and rearranging windings. Firstly, the characteristics of the voltage and detent force are analyzed theoretically and verified by finite element (FEM) simulations. The inductance, thrust and normal forces are then compared with the traditional DS-PMLSM. Furthermore, the geometrical parameters are optimized to improve the thrust. Finally, one DS-PMLSM prototype is tested. The detent force and back EMF tested results verify the effectiveness of the topology proposed in this research.
12 April 2018 in IEEE Transactions on Industrial Electronics
To overcome the disadvantage that the detent force of the permanent magnet linear synchronous motor (PMLSM) with short primary is large, a scheme of the modular PMLSM with flux barriers is proposed in this paper. First, the detent force model is established and verified. The phase-angle characteristics of the harmonics in the detent force waveforms are analyzed. Then, the design principles of the scheme with different sectional combinations are analyzed, and two series of the combinations are demonstrated. The detent force and thrust characteristics of these combinations are subsequently compared. In addition, to improve the thrust density, the auxiliary teeth set at the ends of the sectional primary cores are proposed. Finally, the corresponding conclusions obtained by comparing the modular motors with the traditional motor are presented.
29 May 2019 in IEEE Transactions on Industrial Electronics
Modularization design has been widely used to reduce the detent force of permanent magnet linear synchronous motor (PMLSM). For modular PMLSM, ideally, unit motors are independent of each other and the detent force of the whole motor is the sum of that of unit motors, thus the whole motor detent force can be suppressed by adjusting the phase difference among the unit motor detent forces. But in fact, there is coupling effect between adjacent unit motors, which has adverse effect on the detent force suppression. The influence of the coupling effect is often neglected in current research. Hence, this paper carries out the research on the coupling effect for modular PMLSM: the influence of the coupling effect on the air magnetic field is clarified through magnetic field calculation; the coupling force is isolated by finite element analysis (FEA), and then the effects of key parameters are discussed; the detent force model considering the coupling effect is established, and an optimal design method adjusting the flux barrier length is presented to suppress the detent force.
20 June 2018 in IEEE/ASME Transactions on Mechatronics
This paper introduces Electrically Assisted Turbocharging (EAT) together with the requirements and challenges in selecting an electrical machine for the application. In an effort to identify the most appropriate technology, a detailed, quantitative, multi-domain comparison between Induction, Permanent Magnet and Switched Reluctance Machines an effort is conducted. The study presented puts equal weighing on the electromagnetic, thermal and mechanical sciences, together with the all-important cost and provides clear guidelines on the pros and cons of each machine type for the application in hand. For a real case study, the Induction Machine (IM) is identified as the most suitable candidate due to its high temperature withstand and equalizing capabilities, together with the lower VA requirements. A high performance (10kW, 120krpm) IM is prototyped, and specific suitability aspects demonstrated on actual system-representative tests.