Reducing power losses in engines is considered a key parameter of their efficiency improvement. Nanotechnology, as an interface technology, is considered one of the most promising strategies for this purpose. As a consumable liquid, researchers have studied nanolubricants through the last decade as potential engine oil. Nanolubricants were shown to cause a considerable reduction in the engine frictional and thermal losses, and fuel consumption as well. Despite that, numerous drawbacks regarding the quality of the processed nanolubricants were discerned. This includes the dispersion stability of these fluids and the lack of actual engine experiments. It has been shown that the selection criteria of nanoparticles to be used as lubricant additives for internal combustion engines is considered a complex process. Many factors have to be considered to investigate and follow up with their characteristics. The selection methodology includes tribological and rheological behaviours, thermal stability, dispersion stability, as well as engine performance. Through the last decade, studies on nanolubricants related to internal combustion engines focused only on one to three of these factors, with little concern towards the other factors that would have a considerable effect on their final behaviour. In this review study, recent works concerning nanolubricants are discussed and summarized. A complete image of the designing parameters for this approach is presented, to afford an effective product as engine lubricant.
24 August 2017 in International Journal of Metalcasting
The present study was carried out on ultra-pure aluminum, 1050, and 356 alloys. The results revealed that when Al-4%B is added to ultra-pure aluminum, it forms AlB12 and AlB2 which have no grain refining effect in pure aluminum. When no grain refiner is added to pure aluminum, the microstructure is a mixture of columnar and equiaxed grains. The addition of 30 ppm Ti to pure aluminum is sufficient to promote equiaxed grains when the metal is solidified at high rate ~ 10°C/s but requires an addition of 1000 ppm B at 0.8°C. Increasing the Si content to 7% reduces the initial grain size of pure aluminum from 2800 μm to 1200 μm. In commercial aluminum, B reacts with traces of Ti to form TiB2 phases which are active grain refining agents. However, in Al-7%Si, Ti reacts with Si forming (Al,Si)2Ti phase which is a poor refining agent.
20 July 2018 in International Journal of Cast Metals Research
A study on the effect of different grain refiners and addition technique in Al-7%Si alloys was carried out. The results show that the Al3Ti phase reacts with silicon (Si) in the molten alloy forming a new compound (Al,Si)3Ti. This reaction is independent of the grain refiner addition technique. The temperature of the liquid metal causes a significant change in the Al3Ti phase morphology, which precipitates in the form of platelets at 750°C and in a dendritic form at 950°C. It has also been observed that while (Al,Si)3Ti phase platelets precipitate within the α-aluminum dendrites, the TiB2 or AlB2 particles are rejected into the surrounding interdendritic regions. The results also reveal that addition of 100ppm B will reduce the initial grain size by ~ 85%, which is more than the reduction obtained with the addition of 0.2%Ti in the form of Al-10%Ti (about 65%).
1 January 2018 in Advances in Materials Science and Engineering
The results inferred from the present work show that Al3Ti phase has a strong affinity to react with silicon (Si) in the molten alloy leading to formation of (Al,Si)3Ti phase instead. This reaction is independent of the grain refiner type. The molten liquid temperature would change its morphology from platelets at 750°C into dendritic structure at 950°C. It has also been observed that (Al,Si)3Ti phase platelets precipitate within the α‐aluminum dendrites, whereas TiB2 or AlB2 particles are released into the surrounding interdendritic regions. Introduction of the grain refiner, regardless its type, would cause change in the α‐aluminum dendrite morphology from an elongated to a more rounded form. The results also reveal that addition of 100 ppm B will reduce the initial grain size by ∼85% which is more than the effect of addition of 0.2%Ti in the form of Al‐10%Ti (about 65%). Elimination of undercooling is important to obtain the maximum grain refining effect.