The disinfection of wastewater using nanoparticles (NPs) has become a focal area of research in water treatment. In this study, zinc oxide (ZnO) NPs were synthesized using the microwave heating crystallization technique and characterized using transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). Qualitative well diffusion and quantitative minimum inhibitory concentration (MIC) tests were conducted to determine the antimicrobial activity of ZnO NPs against selected waterborne pathogenic microbes. FTIR spectral studies confirmed that the binding of urea with Zn occurs through Zn–O stretching. XRD confirmed the crystallized identity in a hexagonal ZnO wurtzite-type structure. The formation of zones of inhibition and low MIC values in the antimicrobial analysis were indicative of the effective antimicrobial activity of zinc oxide nanoparticles against the test microorganisms. The application of metallic nanoparticles in water treatment could curb the spread of waterborne microbial diseases.

Mercury is a well-known heavy metal pollutant of global importance, typically found in effluents (lakes, oceans, and sewage) and released into the atmosphere. It is highly toxic to humans, animals and plants. Therefore, the current challenge is to develop efficient materials and techniques that can be used to remediate mercury pollution in water and the atmosphere, even in low concentrations. The paper aims to review the chitosan-based polymer nanocomposite materials that have been used for the environmental remediation of mercury pollution since they possess multifunctional properties, beneficial for the adsorption of various kinds of pollutants from wastewater and the atmosphere. In addition, these chitosan-based polymer nanocomposites are made of non-toxic materials that are environmentally friendly, highly porous, biocompatible, biodegradable, and recyclable; they have a high number of surface active sites, are earth-abundant, have minimal surface defects, and are metal-free. Advances in the modification of the chitosan, mainly with nanomaterials such as multi-walled carbon nanotube and nanoparticles (Ag, TiO₂, S, and ZnO), and its use for mercury uptake by batch adsorption and passive sampler methods are discussed.

Nanotechnology can be defined as the field of science and technology that studies material at nanoscale (1–100 nm). These nanomaterials, especially carbon nanostructure-based composites and biopolymer-based nanocomposites, exhibit excellent chemical, physical, mechanical, electrical, and many other properties beneficial for their application in many consumer products (e.g., industrial, food, pharmaceutical, and medical). The current literature reports that the increased exposure of humans to nanomaterials could toxicologically affect their environment. Hence, this paper aims to present a review on the possible nanotoxicology assays that can be used to evaluate the toxicity of engineered nanomaterials. The different ways humans are exposed to nanomaterials are discussed, and the recent toxicity evaluation approaches of these nanomaterials are critically assessed.

Domestic, agricultural, and industrial waste has been investigated as a substitute for activated carbon adsorbents. For instance, the transformation of tea waste to biochar can be utilized as a substitute for activated carbon adsorbents. In this study, tea waste-based biochar adsorbents (biochar, biochar/reduced graphene oxide (biochar/rGO), biochar/reduced graphene oxide/deep eutectic solvent-cetyltrimethylammonium bromide (biochar/rGO/DES-CTAB), and biochar/reduced graphene oxide/deep eutectic solvent-glycerol (biochar/rGO/DES-glycerol)) were synthesized by simple thermal treatment of tea waste and sucrose followed by modification with reduced graphene oxide and deep eutectic solvents. The obtained materials were characterized using a range of spectroscopy techniques, Fourier Transformed Infrared Spectroscopy (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopy–Energy-Dispersive X-ray Spectroscopy (SEM–EDS), Brunauer, Emmett, and Teller (BET) surface area analysis, and pH at point of zero charge (pH _PZC). The obtained results showed that the principal material, i.e., biochar was modified, and FTIR results confirmed the presence of added functional groups. SEM images revealed surface structural changes, and BET showed a decrease in pore size from 10.16 nm to 6.87 nm. The synthesized materials were applied for the removal of ZDV and phenol from the aqueous medium. Batch adsorption studies were conducted to optimize operating parameters such as the adsorbent dose, solution pH, contact time, and initial concentration. Pseudo-first-order (PFO), Pseudo-second-order (PSO), and intraparticle diffusion (IPD) kinetic models were determined to investigate the mechanism of the adsorption process. The coefficient of correlation, R², was used to determine the best fit of the kinetic models. The adsorption results showed that the DES-glycerol-modified adsorbent was more efficient in removing the pollutants ZDV and phenol than biochar, biochar/rGO, and biochar/rGO/DES-CTAB adsorbents. In addition, the results showed that an acidic medium of pH 2.00 and a contact time of 1 h 30 min and 30 min is sufficient for removing ZDV and phenol, respectively, from an aqueous medium.

A multifunctional nanobiocomposite polymer was developed in this study through a cross-linking polymerization of cyclodextrin with phosphorylated multi-walled carbon nanotubes followed by sol-gel to incorporate TiO₂ and Ag nanoparticles. This work’s novelty was to prove that the developed nanobiocomposite polymer is a potential filter nanosponge capable of removing organic, inorganic, and microorganisms’ pollutants from wastewater samples. The synthesized multifunctional nanobiocomposite polymer was characterized using a range of spectroscopy and electron microscopy techniques. Fourier-transform infrared (FTIR) confirmed the presence of oxygen-containing groups on the developed nanobiocomposite polymer and carbamate linkage (NH(CO)) distinctive peak at around 1645 cm⁻¹, which is evidence that the polymerization reaction was successful. The scanning electron microscopy (SEM) image shows that the developed nanobiocomposite polymer has a rough surface. The Dubinin–Radushkevich and the pseudo-second-order kinetic models best described the adsorption mechanism of Co²⁺ and TCE’s onto pMWCNT/CD/TiO₂-Ag. The efficacy of the developed nanobiocomposite polymer to act as disinfectant material in an environmental media (e.g., sewage wastewater sample) compared to the enriched media (e.g., nutrient Muller Hinton broth) was investigated. From the results obtained, in an environmental media, pMWCNT/CD/TiO₂-Ag nanobiocomposite polymer can alter the bacteria’s metabolic process by inhibiting the growth and killing the bacteria, whereas, in enriched media, the bacteria’s growth was retarded.

Defects both in bulk and at the interfaces serve as charge trapping sites for nonradiative recombination and as ion migration pathways, resulting in degradation of perovskite solar cell efficiency and stability. In this work, a strategy for simultaneous passivation of both bulk and interfacial defects is reported. For bulk passivation polystyrene (PS) is used as an additive in the perovskite precursor which reduces the structural defects by forming larger defect‐free grains. While the F‐PEAI cation is used to passivate the interfacial defects, present at both perovskite HTL/ETL interfaces. Furthermore, by conducting control measurements with just bulk modification (PS), just interface modification (F‐PEAI), and a combination of both, the role of individual defect passivation strategies is decoupled. As a result of simultaneous bulk as well as interfacial passivation, the modified perovskite solar cell shows the highest efficiency of 22.32% with a high V_oc of 1.14 V and fill factor of 80%. Moreover, the cells have excellent stability retaining 92% and 99% of their initial efficiency after 1008 h and 560 h under ISOS‐ D1 and D2 storage conditions. These results highlight the importance of simultaneous bulk and interfacial passivation for improving solar cell efficiency and stability.