A novel miniaturized printed folded dipole antenna has been designed for narrowband sensing applications. It is shown that the antenna may be systematically engineered to achieve matching to a practical source impedance at frequencies well below its half-wavelength resonance using series-LC loading and asymmetrical arm widths. This approach is used to design an inherently well-matched antenna that does not require an external matching network and demonstrates approximately 75% miniaturization, excellent co- to cross-polarization separation, over 24 dB higher realized gain, and strongly improved radiation efficiency relative to an unloaded folded dipole of the same electrically small size. Experimental validation of a fabricated prototype demonstrates excellent agreement with simulations.
Since its inception, ground penetrating radar (GPR) has been a very effective method for examining ice structure. The vast majority of early GPR use was focused on answering questions related to glaciology and ice sheets. More recently, as more and more activity occurs in arctic areas, managing ice structures for a variety of applications has created new uses for GPR. For the past 30–40 years, GPR use for assessing transportation routes over lakes, rivers, and sea ice has been reported, but, only in the last decade has routine application occurred. We have focused on the application of GPR for winter road safety, explained the operational requirements, discussed the current state of practice, and illustrated modern GPR instrumentation. Based on widespread field observations, we have provided information on the ice-layer thickness variation and the variability on GPR ice bottom reflection. Combining extensive GPR and ice auger data provided insight into the variability of electromagnetic wave velocity in ice. Extensive observations showed that velocity varies with ice thickness, and velocities are often considerably lower than observed in “pure” ice.
We provide a coherent approach for developing an understanding of how and where ground-penetrating radar (GPR) can be deployed for tunnel detection. While tunnels in general are of interest, the more specific focus is tunnels that are hand dug or created with a minimal amount of equipment and resources for clandestine purposes. Determining whether GPR can be used for tunnel detection is impossible without an in-depth knowledge of the operational environment and constraints. To effectively address the question, we define the general characteristics of clandestine tunnels, discuss how to estimate the responses amplitude, define the dominant noise types associated with GPR data, and point out how those factors are affected by the GPR system. The key aspects are illustrated using a controlled field case study.
Density is one of the most important parameters in the construction of asphalt mixtures and pavement engineering. When a mixture is properly designed and compacted, it will contain enough air voids to prevent plastic deformation but will have low enough air void content to prevent water ingress and moisture damage. By mapping asphalt pavement density, areas with air void content outside of the acceptable range can be identified to predict its future life and performance. We describe a new instrument, the pavement density profiler (PDP) that has evolved from many years of making measurements of asphalt pavement properties. This instrument measures the electromagnetic (EM) wave impedance to infer the asphalt pavement density (or air void content) locally and over profiles.
Ground-penetrating radar (GPR) systems with multiconcurrent sampling receivers can rapidly acquire dense multioffset GPR data, which are not feasible using typical common-offset (CO) GPR systems with a single fixed offset transmitter-receiver pair. Multioffset GPR data from these new multiconcurrent receiver systems have the potential to be used to create detailed subsurface velocity models and enhanced reflection sections. These are important features that can improve qualitative and quantitative interpretation of GPR data. To realize these benefits and to deal with the large amount of multioffset data generated by these new systems, we have developed an automated and customized data processing workflow. There are three key algorithms that we have developed as part of our workflow, which is crucial for processing large volume, multioffset GPR data so as: first, to efficiently correct and manage time misalignments from multiconcurrent receivers; second, to carry out trace balancing of common-midpoint data for semblance analysis; and third, to automate the velocity analysis step. We showcase our processing workflow using two field data sets acquired using a multiconcurrent sampling receiver GPR system consisting of one transmitter and seven receivers. The field data were collected at two different locations: a site using a system with a 500 MHz center frequency and another site using a system with a 1000 MHz center frequency. We have determined, with both data sets, that our processing workflow could produce automated stacking velocity fields and enhanced zero-offset reflection cross sections. These benefits increase the information that can be used for interpretation (compared with conventional CO data) and can form the basis of further processing steps such as migration. As the cost of these multiconcurrent sampling receiver systems decreases over time, we anticipate their use, and the acquisition of dense multioffset GPR data, to become much more commonplace.