Kaijun Wang

Dr. Kaijun Wang

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2024 in Ceramics International
Verified
Journal Article
Closed access
XZXinyu Zhao
Xinyu Zhao
KWKaijun Wang
Kaijun Wang
ZDZhongshan Deng
Zhongshan Deng
JWJiale Wu
Jiale Wu
YFYongjin Feng
Yongjin Feng
JHJin Hu
Jin Hu

24 June 2021 in Energy Technology
Verified
Journal Article
Closed access
PDF file
KWKaizhao Wang
Kaizhao Wang
JHJin Hu
Jin Hu
TCTianyou Chen
Tianyou Chen
JTJingtao Tang
Jingtao Tang
ZWZhiyi Wang
Zhiyi Wang
KWKaijun Wang
Kaijun Wang

5 January 2024 in Materials
Verified
Journal Article
Open access
PDF file
JWJing Wang
Jing Wang
KWKaijun Wang
Kaijun Wang
JWJiale Wu
Jiale Wu
JHJin Hu
Jin Hu
JMJiangfeng Mou
Jiangfeng Mou
ZDZhong-Shan Deng
Zhong-Shan Deng
Thermoplastic polyurethane (TPU) composites with eutectic gallium (Ga) and indium (In) (eGaIn) fillings of 0 wt%–75 wt% were prepared using the electrostatic spinning method. Field emission scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FTIR) spectroscopy were used to characterize the eGaIn NDs/TPU composites. To evaluate their X-ray shielding properties, Phy-X/PSD and WinXCom were employed to calculate the mass attenuation coefficients, linear attenuation coefficients, half-value layers, tenth value layers, mean free paths, and adequate atomic numbers of the eGaIn NDs/TPU composites. The SEM results indicated that the eGaIn nanodroplets were evenly distributed throughout the TPU fibers, and the flowable eGaIn was well-suited for interfacial compatibility with the TPU. A comparison of the eGaIn NDs/TPU composites with different content levels showed that the composite with 75 wt% eGaIn had the highest μm at all the evaluated energies, indicating a superior ability to attenuate X-rays. This non-toxic, lightweight, and flexible composite is a potential material for shielding against medical diagnostic X-rays.

12 October 2024 in Journal of Energy Storage
Verified
Journal Article
Closed access
JWJiaquan Wu
Jiaquan Wu
KWKaijun Wang
Kaijun Wang
JHJin Hu
Jin Hu
JLJunkai Li
Junkai Li
KWKaizhao Wang
Kaizhao Wang
WZWeijun Zhang
Weijun Zhang

23 March 2022 in Coatings
Verified
Journal Article
Open access
PDF file
HDHuaming Deng
Huaming Deng
KWKaijun Wang
Kaijun Wang
YDYunbiao Duan
Yunbiao Duan
WZWeijun Zhang
Weijun Zhang
JHJin Hu
Jin Hu
The preparation of binary alloys by surfactant-assisted chemical reduction in aqueous solution at room temperature has become a hot topic. In this article low melting point tin/indium (Sn/In) nanoparticles are synthesized. The formation process of the alloy was studied. Scanning electron microscopy, energy spectrometry, and X-ray diffraction are used to determine the morphology, composition, and crystal structure of the nanoparticles. Study found that fully alloyed indium-tin nanoparticles can be obtained by wet chemical method and the main phases of indium-tin alloy are β-phase (In3Sn) and γ-phase (InSn4). However, the Sn phase appears at a low content of indium (40 wt%). When the content of indium increases to 45 (wt%), the tin phase disappears. In addition, the most important finding is that the composition of the indium-tin alloy can be changed by ratio control, and the content of In3Sn increases with the increase of indium content. The relative content of In3Sn attains a maximum when the content of indium increases to 60 (wt%). In contrast, the content of InSn4 decreases. Finally, differential scanning calorimetry measurements is performed to understand the melting behavior of the nanoparticles and low melting temperatures are achieved for a wide range of indium compositions (from 40% to 60%). The melting temperature is found to be in the range of 125–132 °C and it increased with increasing In3Sn (also the increase of indium content). This gives us a new understanding into the binary alloy nano-system and gives important information for the application of low temperature alloy solders. The choice of composition can be based on the corresponding melting point.

8 September 2021 in Energy Technology
Verified
Journal Article
Open access
PDF file
KWKaizhao Wang
Kaizhao Wang
JHJin Hu
Jin Hu
TCTianyou Chen
Tianyou Chen
JTJingtao Tang
Jingtao Tang
ZWZhiyi Wang
Zhiyi Wang
KWKaijun Wang
Kaijun Wang
A room-temperature liquid metal battery with a solid lithium anode electrode and gallium–tin (Ga–Sn) alloy cathode electrode is reported. The Li‖Ga–Sn battery has fast reaction kinetics, a satisfactory specific capacity, high energy efficiency, good rate performance, and stable cyclic reversibility, which is a promising choice for power grid energy storage applications. More details can be found in article number 2100330, Jin Hu, Kaijun Wang, and co-workers.