Liu Pang-Jung

Prof. Liu Pang-Jung


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 April 2016 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
CYChia-Hung Yen
Chia-Hung Yen
To reduce circuit complexity and better control the charging current for parallel charging, a switching-based charger with an adaptive hybrid duty cycle control (AHDCC) for multiple batteries is presented. Depending on the voltage difference of the batteries, the AHDCC mechanism automatically delivers a different amount of energy to each battery to realize battery voltage balance and reduce power losses. Since an intermittent charging method is adopted in the constant current (CC) mode, the effect of voltage drop across the battery's parasitic resistor can be removed, and thus the charging time in CC mode is prolonged. AHDCC adjusts the charging current, prolongs the charging period in CC mode, and entirely turns on the auxiliary switches in the constant voltage mode. As a result, the functionalities of fast charging and battery voltage balance can be realized concurrently. The experimental results demonstrate that the peak efficiency of the charger is up to 89.4% and the total charging time of two batteries is slightly smaller than that of a single battery.

10 October 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
LCLin-Hao Chien
Lin-Hao Chien
A high-efficiency multimode battery charger with an adaptive supply voltage (ASV) control scheme is presented in this paper. The proposed battery charger includes a charging circuit and a dc-dc buck converter. The charging circuit automatically switches among trickle current (TC), constant-current (CC), and constant-voltage (CV) modes corresponding to the battery voltage while the buck converter with ASV control generates an adaptive supply voltage to closely track the battery voltage, leading to significant reduction in the power loss of the charging circuit. To further enhance the efficiency of the battery charger, zero current detection and non-switching control schemes are employed to decrease the power consumption of the buck converter in TC and CV modes. The battery charger was implemented with a 0.35-μm CMOS 2P4M process. The experimental results are shown to verify the theoretical analysis of the proposed charger. The maximum efficiency of the overall system is 88.3%, and the maximum efficiency improvement between the proposed charger and the conventional linear charger with fixed supply voltage is up to 11.6%.

7 February 2012 in IEEE Transactions on Circuits and Systems for Video Technology
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
YCYi-Jan Emery Chen
Yi-Jan Emery Chen
This paper presents a compact 10-bit digital-to-analog converter (DAC) for LCD source drivers. The cyclic DAC architecture is used to reduce the area of LCD column drivers when compared to the use of conventional resistor-string DACs. The current interpolation technique is proposed to perform gamma correction after D/A conversion. The gamma correction circuit is shared by four DAC channels using the interleave technique. A prototype 10-bit DAC with gamma correction function is implemented in 0.35 μm CMOS technology and its average die size per channel is 0.053 mm2, which is smaller than those of the R-DACs with gamma correction function. The settling time of the 10-bit DAC is 1 μs, and the maximum INL and DNL are 2.13 least significant bit (LSB) and 1.30 LSB, respectively.

21 November 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
WCWei-Yi Cheng
Wei-Yi Cheng
LCLin-Hao Chien
Lin-Hao Chien
JLJing-Yuan Lin
Jing-Yuan Lin
This article proposes a configurable supply mechanism in the power stage to simultaneously improve the load transient response and power conversion efficiency. The power stage, comprising a dc–dc converter and an auxiliary power circuit (APC), can be organized depending on the variable load conditions. During step-load changes, the APC can provide an additional charging or discharging current to the output capacitance of the dc–dc converter to compensate for any differences between the load current and inductor current. Meanwhile, two auxiliary transient transistors are employed to immediately adjust the output level of the error amplifier because the peak current-mode control is used in the dc–dc converter. Thus, the recovery time and output transient ripple are enhanced significantly. At the steady state, the APC is inactivated; thus, the conversion efficiency of the dc–dc converter does not degenerate. Above medium loads, only the dc–dc converter is activated to deliver adequate power with high efficiency. At light loads, the APC acts as a linear regulator to take over the energy delivery scheme because power consumption is reduced effectively while the output voltage is kept. Therefore, the hybrid operation can guarantee improvements in load transient response and power conversion efficiency at light loads. The proposed converter was fabricated with 0.35- μ m CMOS technology. The experimental results showed that the recovery times for 450-mA step-down and step-up loads are 1.6 and 2.0 μs, respectively. Comparing to when the transient mode is disabled, the recovery time of the output voltage is improved by over ten times when the transient mode is enabled. Further, the efficiency improvements with the proposed method at load current of 20 mA under the output voltages of 2.5 V and 1.8 V are 13.8% and 4.9%, respectively.

15 June 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
CLChen-Yu Liao
Chen-Yu Liao
MKMao-Hui Kuo
Mao-Hui Kuo
This paper presents an active ripple cancelation (ARC) technique for reducing the switching harmonics of the output voltage of a dc-dc converter. An ARC module injects an ac current to accurately cancel the inductor current ripple while the switching converter provides the dc output current. As a result, the output spur of the switching converter can be reduced effectively. However, due to the ARC module, the proposed power converter includes two complex poles. To ensure the system stability and achieve accurate ripple cancelation, a proposed control method and an adaptive phase-lock circuit are utilized. Furthermore, the ripple cancelation capability is independent of duty cycle, load current, and other converter parameters. The measurement results demonstrate that the switching spur reduction with ARC technique can achieve 28 dB while the noise floor is kept the same.

15 January 2018 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
LPLiu Pang-Jung
Liu Pang-Jung
YHYu-Chi Hsu
Yu-Chi Hsu
SHShang-Ru Hsu
Shang-Ru Hsu
An LED driver consisting of dimmable current balancing circuits (CBCs) and a boost converter with drain voltage balance (DVB) and phase-shifted pulsewidth modulation (PSPWM) control schemes is presented. To reduce the power loss on conventional linear current regulators, CBCs are employed. The DVB control scheme is proposed to maintain a desired constant voltage across the CBCs, so as to increase current balance and achieve high efficiency of the CBCs. Thus, the bus voltage of the boost converter is adaptively regulated based on the DVB control. The PSPWM control scheme can alleviate the variation of the bus current provided by the boost converter. As a result, the transient ripple of the bus voltage can be reduced when the light-emitting diode (LED) strings are turned on and off. Furthermore, the utilization of DVB control is increased when the PWM dimming duty cycle becomes lower. The experimental results demonstrate that the minimum voltage among the CBCs is always kept at the lowest constant level while maintaining the required current passing through the LED strings. The efficiency of the CBCs is kept almost the same for different LED currents and is over 95%. Thus, a high-efficient parallel-string dimmable LED driver with simple circuitry can be achieved.